Thanks Jim. Or, as my daughter says, “Preesh”.

https://github.com/mykle1/MMM-EARTH-Live

Glad to see it’s working again.

Thanks mate. Me too! Let me know if you have any other troubles with it.

The API only just started have troubles recently. Up one day, down the next. This is not typical. They (NASA) have been very reliable until this point. Please give it a little time to be corrected. I’ll make an announcement here when it’s working again. I’m sure you’ll enjoy it then. The imagery is fantastic and current.

I looked into the data coming from the API. You can tell by the abundance of “null” responses that something is amiss with their data. The image: key shows an image name but the date: key is null, making it impossible to retrieve the image as the module code is written. Hopefully, they will fix the data as quickly as they did last week.

Thank you very much , love the module.

Thanks dude. I love it as well. Been on my mirror since it was born. I’ll keep you posted

Is anyone else having a loading issue today with this module? I just put it on the other day and today after a reboot it stopped loading, all i see is hello mother earth.

This same thing happened 4 days ago and was resolved at the API source. Obviously, they are having some troubles on their end. I’m sorry about that. I will make another announcement when the API corrects the issue.

YAY!!! :face_with_tears_of_joy: :face_with_tears_of_joy:

Anyone that experienced problems with MMM-EARTH yesterday can breathe a sigh of relief. It was not the module that was at fault. It was the API. Whatever problems they were having seem to be over. The module is now working as intended.

Yes, keep your API keys private. Use the config options to your liking. If you like the fade, keep it. It’s up to you.

We’re all learning, Peter. At least, I hope so. I’m glad it’s working for you now. Peace! :-)

Pay close attention. When it fades and comes back, is the picture different? It should be. Watch a few times to see please. If you do not want the fade in/ fade out then you can add this to your config entry for EARTH
animationSpeed: 0,

Hello Peter. It is not your config that is causing the EARTH not to spin. I just loaded your config and it rotates the EARTH every 15 seconds as per rotateInterval: 15000,. Have you waited 15 seconds?
Are you expecting it to rotate more quickly? Or is it not updating at all?

One thing I did notice about your config:

{
			module: "",
			position: "lower_third"
		},

An empty module name

Also, you should remove your API keys before you post on the forum. You can remove yours from here by clicking the three dots at the bottom right of your post and choose EDIT.

Lastly, I see you are using 20% MaxWidth and MaxHeight in MMM-EARTH, and that’s just fine, but you can also choose mode: "naturalThumb", at 100% to achieve the same thing with less system load on your Pi. But let’s get you fixed up first. :-)

/* Magic Mirror Config Sample
 *
 * By Michael Teeuw http://michaelteeuw.nl
 * MIT Licensed.
 *
 * For more information how you can configurate this file
 * See https://github.com/MichMich/MagicMirror#configuration
 *
 */

var config = {
	address: "localhost", // Address to listen on, can be:
	                      // - "localhost", "127.0.0.1", "::1" to listen on loopback interface
	                      // - another specific IPv4/6 to listen on a specific interface
	                      // - "", "0.0.0.0", "::" to listen on any interface
	                      // Default, when address config is left out, is "localhost"
	port: 8080,
	ipWhitelist: ["127.0.0.1", "::ffff:127.0.0.1", "::1"], // Set [] to allow all IP addresses
	                                                       // or add a specific IPv4 of 192.168.1.5 :
	                                                       // ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.1.5"],
	                                                       // or IPv4 range of 192.168.3.0 --> 192.168.3.15 use CIDR format :
	                                                       // ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.3.0/28"],

	language: "nl",
	timeFormat: 24,
	units: "metric",

	modules: [
		{
    			module: "MMM-EARTH",
    			position: "top_center",
    			config: {
        		mode: "Natural",
        		rotateInterval: 15000,
        		MaxWidth: "20%",
        		MaxHeight: "20%",
    		}
		},
		{
			module: "updatenotification",
			position: "top_bar"
		},
		{
			module: "clock",
			position: "top_left"
		},
		{
			module: "calendar",
			header: "Feestdagen",
			position: "top_left",
			config: {
				calendars: [
					{
						symbol: "calendar-check-o ",
						url: "https://www.mozilla.org/media/caldata/DutchHolidays.ics"
					}
				]
			}
		},
		{
			module: "",
			position: "lower_third"
		},
		{
			module: "currentweather",
			position: "top_right",
			config: {
				location: "Apeldoorn,Netherlands",
				locationID: "",  //ID from http://www.openweathermap.org/help/city_list.txt
				appid: "Xxxxxxxxxx"
			}
		},
		{
			module: "weatherforecast",
			position: "top_right",
			header: "Weersvoorspelling",
			config: {
				location: "Apeldoorn,Netherlands",
				locationID: "",  //ID from http://www.openweathermap.org/help/city_list.txt
				appid: "Xxxxxxxx"
			}
		},
		
		{
			module: "newsfeed",
			position: "bottom_bar",
			config: {
				feeds: [
					{
						title: "Nu.nl",
						url: "http://www.nu.nl/rss/Algemeen"
					}
				],
				showSourceTitle: true,
				showPublishDate: true
			}
		},
	]

};

/*************** DO NOT EDIT THE LINE BELOW ***************/
if (typeof module !== "undefined") {module.exports = config;}

Thanks!
Peter

[card:mykle1/MMM-EARTH]

Update Version 1.0.2

NASA changed their data AGAIN without consulting me AGAIN.

The nerve!

So, once again, a git pull in your MMM-EARTH directory should set things to right, AGAIN. :^)