I have a RPi 3B+ with Buster on it, and it works ok, though I can’t have screencast and remote installed at the same time. So I wanted to make a new install, and I downloaded the RaspberryOS Bullseye 32bit.
With that I can run the two modules together, but now I can’t rotate the screen to portrait.
The old version was just a question of adding display_hdmi_rotate=1 to the /boot/config.txt, but this doesn’t work with bullseye.
So how do I rotate the screen on the Bullseye?
I tried doing it from inside ‘X’ by using the Screen Configuration app, but when I do that (rotation=left), the screen goes black, and nothing happens, I can’t press the ‘verify’ button, so if I reboot it, it is still in landscape mode.
What can I do?
Read the statement by Michael Teeuw here.
Posts made by fribse
-
RPi 3B+ with 'Bullseye' can't rotate screen?
-
RE: Just updated MagicMirror today, and now I "0|MagicMirror | sh: 1: ./node_modules/.bin/electron: not found"
@sdetweil Hi there, yes I did, and I ran it again, and then it worked.
But thanks for the hint! -
Just updated MagicMirror today, and now I "0|MagicMirror | sh: 1: ./node_modules/.bin/electron: not found"
I was on 2.18, and got a notification that there was a new version, and today I finally tried to update it, and now I see this message in the logfile
0|MagicMirror | sh: 1: ./node_modules/.bin/electron: not foundThe software is installed with @sdetweil 's script originally.
What to do?
-
RE: Starting over on MM install - still shows errors
@sdetweil Ok, good to know, so at least it’s not them making problems for MMM-ScreenCast and MMM-RemoteControl.
-
RE: Starting over on MM install - still shows errors
So I did a new install completely from scratch on a Raspbian Buster, and did a ‘manual’ install this time, still same error:
[25.02.2022 16:00.46.615] [LOG] Launching application.
[1789:0225/160048.427469:ERROR:viz_main_impl.cc(161)] Exiting GPU process due to errors during initialization
[1828:0225/160048.917933:ERROR:sandbox_linux.cc(376)] InitializeSandbox() called with multiple threads in process gpu-process.Monitor is in portrait mode, these settings are in boot/config.txt
display_rotate=1 enable_uart=1 avoid_warnings=1
-
Starting over on MM install - still shows errors
Hi Guys
I’m having some problems with the installation.
I’ve done a brand new Raspbian Buster install.
Fully updated.
I then ran @sdetweil 's install script.I’m now modifying the module config one by one, and installing the custom modules.
I’ve yet to install a custom module, so far I have changed the software to da-DK, I’ve made the compliments module fetch my gist compliments file, and I’ve changed the calendar module to use a danish provider.
I already see these two messages:
0|MagicMirror | [3635:0225/103036.868905:ERROR:viz_main_impl.cc(161)] Exiting GPU process due to errors during initialization 0|MagicMirror | [3680:0225/103037.331723:ERROR:sandbox_linux.cc(376)] InitializeSandbox() called with multiple threads in process gpu-process.
-
RE: My Mirror reboots for no reason
@lhops Try to log your temperature, the reboot sounds like a temp issue.
It would also suit the PiR that registers a rising temperature. -
MMM-Mycommute - has anybody gotten the time start and end, and hidedays to work?
I live in CEST timezone, and I fear that is part of the problem.
I have a config like this for the module:{ module: "MMM-MyCommute", position: "bottom_right", classes: "xsmall", header: "Trafik", config: { apiKey: "xxx", startTime: "05:00", endTime: "12:00", hideDays: [0,6], origin: "Home", destinations: [ { destination: "Address1", label: "Company1", mode: "driving", color: "#82E5AA" }, { destination: "Address2", label: "Company2", mode: "driving", color: "#82E5AA" } ] } },
My hope was that it would be active between 5 in the morning and midday, and not show up in weekends.
But this morning (tuesday) it diedn’t show up at around 8.Has anybody else gotten this to work, and is there a trick to it?
-
RE: Just upgraded to 2.18, runs, but no display
@fribse Nope, just removed it and booted the mirror, still seeing those…