Python - One momentary switch, LED, and a shut-off timer

Unbored

Working on programming a LED strip lights around the mirror, with a single push button. I am good with the GPIOs and the relay required, but seeking some guidance on the code

First button press: Lights activate. Have the option to move to the second button press or if the button is not pressed a second time, then the side lights will turn off automatically after 30 minutes.
Second button press: Lights turn off and python is waiting for the first button press (again).

Below is one version that I been working on where I wanted to divide the lights (side lights (“low”), then side&top lights (“high”), then all off), but at this point I would settle for just all lights at the same time.

The auto-shutoff is required to ensure they aren’t left on for days at time.

It is possible that I need to pull in another module, but I can’t seem to hack my way into figuring out the shutoff timer or where to place it, so it is time to call in a lifeline. Thanks.

import RPi.GPIO as GPIO
from time import sleep

GPIO.setmode(GPIO.BCM)

LEDPinLow = 26
LEDPinHigh = 22
buttonPin = 5

# Setup the pin the LED is connected to
GPIO.setup(LEDPinLow, GPIO.OUT)
GPIO.setup(LEDPinHigh, GPIO.OUT)

# Setup the button
GPIO.setup(buttonPin, GPIO.IN, pull_up_down = GPIO.PUD_UP)

buttonPress = True
ledStateLow = False
ledStateHigh = False

while (1):
        print("Press it")
        buttonPress = GPIO.input(buttonPin)
        if buttonPress == False and ledStateLow == False and ledStateHigh == False:
            GPIO.output(LEDPinLow, True)
            GPIO.output(LEDPinHigh, False)
            print("LED ON - Side lights only")
            ledStateLow = True
            ledStateHigh = False
            sleep(.25)
            
        elif buttonPress == False and ledStateLow == True and ledStateHigh == False:
            GPIO.output(LEDPinLow, True)
            GPIO.output(LEDPinHigh, True)
            print("LED ON - Side and Top Lights ")
            ledStateLow = True
            ledStateHigh = True
            sleep(0.25)

        elif ledStateLow == True and ledStateHigh == True:
            sleep(5)
            GPIO.output(LEDPinLow, False)
            GPIO.output(LEDPinHigh, False)
            print("LEDs OFF")
            ledStateLow = False
            ledStateHigh = False
            sleep(0.5)

        sleep(0.15)

Unbored

Re: Python - One momentary switch

I found the answer over on stackexchange and figured I would share. The mirror is a college graduation present for my youngest daughter; she requested the light ring (I heard the word make-up followed by blah, blah, blah, blah…, kidding of course.). The 30 minute timer was not a joke, there’s no way I am leaving responsibility of turning off the light to a college grad

I am still working on it and will post a thread in the correct forum when it is done.

The answers are here: https://raspberrypi.stackexchange.com/questions/66639/python-one-momentary-switch-led-and-a-shut-off-timer?answertab=active#tab-top

#!/usr/bin/env python

import time
import pigpio

LEDPin = 26
buttonPin = 5

LEDOn = False
minutesOn = 0

def callback(gpio, level, tick):
   global minutesOn, LEDOn
   if level == 0: # button press
      if LEDOn:
         print("LED off")
         LEDOn = False
         pi.write(LEDPin, 0)
      else:
         print("LED on")
         LEDOn = True
         pi.write(LEDPin, 1)
         minutesOn = 0
   elif level == pigpio.TIMEOUT:
      if LEDOn:
         minutesOn += 1
         print("LED on for {} minutes".format(minutesOn))
         if minutesOn >= 30:
            print("LED off")
            LEDOn = False
            pi.write(LEDPin, 0)

pi = pigpio.pi()
if not pi.connected:
   exit()

# Setup the pin the LED is connected to
pi.set_mode(LEDPin, pigpio.OUTPUT)

# Setup the button
pi.set_mode(buttonPin, pigpio.INPUT)
pi.set_pull_up_down(buttonPin, pigpio.PUD_UP)
pi.set_glitch_filter(buttonPin, 5000)

pi.set_watchdog(buttonPin, 60000)  # watchdog every minute

cb = pi.callback(buttonPin, pigpio.EITHER_EDGE, callback)

while True: # all the work is done in the callback
   time.sleep(1)

Unbored

Here’s a pic of the work in progress.
alt text