Hello!
I know there are many articles addressing this already, but I haven’t found one to work yet so hoping someone can shed new light.
MM 2.7.0 on an RaspberryPi Zero W and chromium
MM was working after initial setup, I was tweaking modules just to get my initial layout all set (occasionally getting the “please use a config.js” message, fixing my js then it worked again…
So now the issue:
Twice now after pm2 restart mmrestart
from just changing config.js I get the browser page that the Site can't be reached... localhost refused to connect
1st time it happened I started going back through the whole setup again doing npm install, etc and nothing worked. I was just about to burn the whole thing down when…
Finally after one more sudo reboot
after no changes… it just worked.
This time, it’s not coming back yet.
tail -n 50 ~/.pm2/logs/mmstart-out.log:
wm_set_cursor_visibility: visible using XCreateFontCursor
Starting MagicMirror: v2.7.1
Loading config ...
Loading module helpers ...
No helper found for module: alert.
Initializing new module helper ...
Module helper loaded: updatenotification
No helper found for module: clock.
Initializing new module helper ...
Module helper loaded: MMM-CalendarExt
Loading module helpers ...
No helper found for module: alert.
Initializing new module helper ...
Module helper loaded: updatenotification
No helper found for module: clock.
Initializing new module helper ...
Module helper loaded: MMM-CalendarExt
Whoops! There was an uncaught exception...
MagicMirror will not quit, but it might be a good idea to check why this happened. Maybe no internet connection?
If you think this really is an issue, please open an issue on GitHub: https://github.com/MichMich/MagicMirror/issues
wm_set_cursor_visibility: visible using XCreateFontCursor
Starting MagicMirror: v2.7.1
Loading config ...
Loading module helpers ...
No helper found for module: alert.
Initializing new module helper ...
Module helper loaded: updatenotification
No helper found for module: clock.
Initializing new module helper ...
Module helper loaded: MMM-CalendarExt
Loading module helpers ...
No helper found for module: alert.
Initializing new module helper ...
Module helper loaded: updatenotification
No helper found for module: clock.
Initializing new module helper ...
Module helper loaded: MMM-CalendarExt
Whoops! There was an uncaught exception...
MagicMirror will not quit, but it might be a good idea to check why this happened. Maybe no internet connection?
If you think this really is an issue, please open an issue on GitHub: https://github.com/MichMich/MagicMirror/issues
nmap -A -T4 localhost:
Starting Nmap 7.40 ( https://nmap.org ) at 2019-04-24 06:55 EDT
Nmap scan report for localhost (127.0.0.1)
Host is up (0.0021s latency).
Other addresses for localhost (not scanned): ::1
Not shown: 998 closed ports
PORT STATE SERVICE VERSION
22/tcp open ssh (protocol 2.0)
| fingerprint-strings:
| NULL:
|_ SSH-2.0-OpenSSH_7.4p1 Raspbian-10+deb9u4
| ssh-hostkey:
| 2048 66:12:9f:31:9f:17:1c:07:1e:f4:73:e5:66:95:ea:1a (RSA)
|_ 256 17:08:1d:39:a9:ff:3f:1d:5a:66:c7:2a:e6:36:78:5f (ECDSA)
111/tcp open rpcbind 2-4 (RPC #100000)
| rpcinfo:
| program version port/proto service
| 100000 2,3,4 111/tcp rpcbind
|_ 100000 2,3,4 111/udp rpcbind
1 service unrecognized despite returning data. If you know the service/version, please submit the following fingerprint at https://nmap.org/cgi-bin/submit.cgi?new-service :
SF-Port22-TCP:V=7.40%I=7%D=4/24%Time=5CC040A8%P=arm-unknown-linux-gnueabih
SF:f%r(NULL,29,"SSH-2\.0-OpenSSH_7\.4p1\x20Raspbian-10\+deb9u4\n");
Service detection performed. Please report any incorrect results at https://nmap.org/submit/ .
Nmap done: 1 IP address (1 host up) scanned in 23.12 seconds
/etc/hosts/:
127.0.0.1 localhost
::1 localhost ip6-localhost ip6-loopback
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
127.0.1.1 juddpi
sudo iptables -L --verbose:
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Any help is greatly appreciated.
Thanks, all!