Issues with MMM-PIR

ingo916

		{
			module: 'MMM-Pir',
			position: 'top_left',
			config: {
				debug: false,
				delay: 2 * 60 * 1000,
				turnOffDisplay: true,
				mode: 10,
				ecoMode: true,
				displayCounter: false,
				//displayCounter: true,
				displayBar: false,
				//displayBar: true,
				displayStyle: "Circle",
				displayLastPresence: false,
				//displayLastPresence: true,
				lastPresenceTimeFormat: "LL H:mm",
				mode6_gpio: 20,
				mode6_clearGpioValue: true,
				pir_gpio: 22,
				//pir_gpio: 21,
				pir_reverseValue: false,
				xrandrForceRotation: "normal",
				wrandrForceRotation: "normal"
			}
		},

eyesallin

@bugsounet

Thanks for your patience, this is what i get.

admin@garyspi:~ $ groups
admin adm dialout cdrom sudo audio video plugdev games users input render netdev lpadmin gpio i2c spi
admin@garyspi:~ $

schris88

your config looks good thus far, if you´re not getting it to run you can try my solution which is currently running like a charm

I installed it with MMM-Pir-Sensor-light and changed the code to use wayland,
to toggle the display on Pi5 this is working on a fresh OS install

WAYLAND_DISPLAY=“wayland-1” wlr-randr --output HDMI-A-1 --off
WAYLAND_DISPLAY=“wayland-1” wlr-randr --output HDMI-A-1 --on

possible outputs HDMI-A-1 (the one right next to usb-c), HDMI-A-2

If you monitor turns back on by itself after ~10 secs add “vc4.force_hotplug=1”(1=hmdi1 / 2=hdmi2 / 3=both) to the end of your /boot/firmware/cmdline.txt without creating a new line

All I did was change the command in activate and deactivate display function in the node_helper.js and added the cmdline parameter (dont forget to reboot)

eyesallin

@eyesallin
I’m beginning to think that all this is Pi 5 related.
Also changing to mode 10 as previously stated screws with the weather modules which don’t load. Remove MMM-PIR from config and everything works fine.
It doesn’t help that I’m completely new to all this.

schris88

@eyesallin yes it´s an “issue” with the pi5 as the os is now using wayland as graphical environment instead of x11 which was used forever, a lot of tools are written for it and now need to be updated to work with wayland. You will find a lot of scenarios where there is no updated tool or alternative for the pi5 atm. The switch was done end of 2023 so it´s very new.

eyesallin

@schris88
Thx for the info, I guess a lot of the modules require reworking for the Pi 5.
Unfortunately I do not have the ability, totally new to the Pi and programming.

ChanceTime

Is anyone able to get MMM-PIR successfully running on Bookworm? Feels like every option I’ve tried to turn my screen on and off after the PIR senses movement has been a struggle with no results. I’ve confirmed with tests that my sensor is working, but all the old ways to trigger the display on-off behaviour seem to not be running. I’m on a Pi4 running 12 with Wayland.

Unfortunately I can’t go back to 11 because 10 worked like a dream, and 11 for some reason i could never successfully troubleshoot would refuse to load a taskbar in. Hardware seems to be working fine again in 12…

I can post my config if it helps. Thanks for the hard work, bugsounet. :)

sdetweil

@ChanceTime bookworm on pi4 or 5 uses a different window manager, Wayland, and requires different commands

you can go back to xorg by using the raspi-config command

diccon

Hi

I have had MMM-Pir module running perfectly for months. When I updated my RPi 3B+ to the latest updates this week the module produce the same error message

Pir Error Detected: EINVAL: invalid argument, write

I have tried reinstalling the module but no luck.

Any help greatly appreciated

Thanks

sdetweil

@diccon which MMM-PIR?