MMM-Navigate, Navigation inside MagicMirror with Rotary Encoder

AxLed

thanks for feedback.
first:
Idea A:

maybe the pin 19 is the problem, because it is not only a GPIO pin rather it has SPI features. Can you change to BCM16 (and change it in config.js as well) and try it?

Idea B:

Do you use capacitors for debouncing? If not, you can change debouncing value of following line: https://github.com/Ax-LED/MMM-Navigate/blob/master/node_helper.js#L37

second:

Which module should start hidden? MMM-Navigate?

third:
I tried to reproduce on my pi 3 and get no error, so i checked the code.
You can add following line as new line 19 in node_helper.js
var lastdir = '';

AxLED

keineAhnung123

@AxLed
I will try that later. Thanks
And yes, i want to start MMM-Navigate hidden. Is that possible?

AxLed

@keineAhnung123 ,

informations to your second issue:
Your request is not provided by MMM-Navigate, maybe it is possible with one of the following modules (untested):

AxLED

keineAhnung123

Hello @AxLed

first

Idea A: didnt solve the problem. Still no click
Idea B: I tried capacitors and software debouncing. Still no click

I will use this python script to get the click working:

import RPi.GPIO as GPIO
GPIO.setmode(GPIO.BCM)
BUTTON_PIN = 16
GPIO.setup(BUTTON_PIN, GPIO.IN, pull_up_down = GPIO.PUD_UP)

and start it within node_helper.js:

var child_process = require('child_process');

module.exports = NodeHelper.create({
	// Subclass start method.
  start: function() {
		var self = this;
		this.loaded = false;
		this.createRoutes();
		child_process.execFile('python', ['/home/pi/MagicMirror/modules/MMM-Navigate/ky-040-initialisieren.py']);
	},

Now it works.

Btw: In intializeRotary-function (node_helper.js) there ist a CLK and DT.read and also a CLK and DT.watch instruction. For the SW there is only a SW.watch but not a read instruction. Is that right? Just wanted to mention. Im not an expert in programming.

third
Yes, the error is gone :)

AxLed

@keineAhnung123 ,

thanks for your patience.
to first:
it seems to be something with the pullup / pulldown resistors, see also https://github.com/fivdi/onoff#configuring-pullup-and-pulldown-resistors
See also the new “gpio” config command (https://www.raspberrypi.org/forums/viewtopic.php?f=117&t=208748)
So here is another idea, can you try (based on informations mentione above):

(i suppose your SW pin is 16)
add following line in /boot/config.txt
gpio=16=ip,pu
Meaning: sets your GPIO 16 as input (ip) and pull up (pu)
if this doesnt work try:
gpio=16=ip,pd
Meaning: sets your GPIO 16 as input (ip) and pull down (pd)

Maybe this way MMM-Navigate works without the python script.

To SW.watch you mentioned, this is ok, as i dont need to know the initial state of SW.

to third:

i added the line in node_helper.js in the github repo.

Regards

AxLED

keineAhnung123

@AxLed Now it works with gpio=16=ip,pu
Do the changes in boot.txt affect the Raspberry Pi in any way i have to know?

Thanks a lot so far :)

AxLed

@keineAhnung123,

great to hear it works, i will update the readme at github.
The line in config.txt only tells the pi at boottime, that GPIO16 is set to input and the internal resistor is set to pullup. So there is nothing else to know unless you change your GPIO Pins for something else.
@Eisblume maybe this is a solution for your issue.

AxLED

robiv8

@AxLed
also a great modul from you :-)

I have tested and works fine. Two questions.

When I press any selection, the module disappears.
It fades out and the module below it jumps up. Why?

Is it possible to control the MMM-Dreambox module with it? That would be great, of course.

Thanks in advance

AxLed

@robiv8

the modul MMM-Navigate disappears by design. If it is faded out and you use rotary or button it comes back on (fades in).

Yes MMM-Dreambox can be controlled bei MMM-Navigate, see https://github.com/Ax-LED/MMM-Dreambox#further-options

AxLED

robiv8

@AxLed
Hallo,
is there a way to deaktivate this Fade out? i want it olways on.
Thanks Robi

OK Sorry, i found it by my self :-)
in MMM-Navigate.js
// this.hide(10000);