Need help with MMM-MQTTbridge not "communicating" with MMM-RTSPStream

[sdetweil]

@Cr4z33 same rtspstream, that part of your solution didn’t change

button -> ha automation -> mqtt publish -> mqttbridge -> notification to rtspstream to open and connect video feed

altho you may have to use
https://github.com/evroom/MMM-MPlayer
instead of rtspstream module

and install MMM-ViewNotifications to see the events sent inside MagicMirror

[Cr4z33]

@sdetweil hmm I want to give it a try tomorrow morning (GMT+2).

Would you mind if I might contact you by PM just in case? 🥺

[sdetweil]

@Cr4z33 no problem. i am US Central UTC-5

[wishmaster270]

@Cr4z33
Hi and sorry fir the late reply…
Your config of the MQTT module is still missing a “debug: true”. The messages only get logged if debugging is enabled.

	{
		module: 'MMM-MQTTbridge',
		disabled: false,
		config: {
                        debug: true, 
			mqttServer: "mqtt://:@ipaddress:port",
			mqttConfig:
			{
				listenMqtt: true,
				interval: 500,
			},
			notiConfig:
			{
				listenNoti: true,
				ignoreNotiId: ["CLOCK_MINUTE", "NEWS_FEED"],
				ignoreNotiSender: ["system", "NEWS_FEED"],
			},
			// set "NOTIFICATIONS -> MQTT" dictionary at /dict/notiDictionary.js
			// set "MQTT -> NOTIFICATIONS" dictionary at /dict/mqttDictionary.js
			},
	}

[sdetweil]

@wishmaster270 yes, we covered that before
https://forum.magicmirror.builders/post/126008

[sdetweil]

@wishmaster270 i’ve come to the conclusion

the doorbell itself does not publish to mqtt
MqttBridge did not get any message from its subscribe

he is going to try to build a HomeAssistant automation, as it CAN see the doorbell button thru its integration

[Cr4z33]

@wishmaster270 thanks for spending some time on my issue although you’re busy.
As sdetweil said he’s already helping me into this. 🙂

@sdetweil my bad, my bad and again my bad! 😓

I was going to tryout your method when I realized I actually never checked deeply what was outputting npm start… There’s A LOT of doorbell data being captured by MMM-MQTTbridge indeed! 🤦🏼

You can see here the output.

Can you see at this point (maybe) some additional data that needs to be added to mqttDictionary.js or do you still believe I should go your way (HA, automation, etc.)?

While waiting for your kind reply I will play at trying your method. 😁

[rkorell]

@Cr4z33 Good afternoon,
I do not have the time to dig too deep into MMM-MQTTbridge …
But what I see checking your console logfile and compare this to your first posting:
You obviously had managed that the MQQT message arrives and is acknowledged.

.
The message you receive is:

{
    "Action": "Pulse",
    "Code": "Invite",
    "Data": {
        "CallID": "5",
        "IsEncryptedStream": false,
        "LocaleTime": "2025-04-30 10:40:43",
        "LockNum": 2,
        "RealUTC": 1746002443,
        "SupportPaas": false,
        "TCPPort": 37777,
        "UTC": 1746006043.0,
        "UserID": "101"
    },
    "Index": 0,
    "deviceType": "DHI-VTO3311Q-WP",
    "serialNumber": "****"
}

This is what you trying to capture in your mqttDisctionary.js
I’m not 100% sure if you

1. catch the right data-value : - is your jsonpath correct?
2. is “notiID” the right place for the module name you try to reach?

Just spontaneous thoughts about your issue - maybe misleading …

Regards,
Ralf

[Cr4z33]

@rkorell hi it’s a good question indeed.

However too bad that I am not skilled enough to know the answer lol that’s why I am posting here asking for help! 😂

Let’s see if @sdetweil or someone else can find out.

[sdetweil]

@Cr4z33 woohoo, i see the data, now its MQTTBridge configuration, and that part i dont know (yet)