PIR Sensor ??

[sdetweil]

@mdlefevere they all use the same 4 commands

tvservice
vcgencmd
dpms
cec-client

top three turn off hdmi, leaving the ugly message
cec-client turns off the display, BUT, needs something 2018 or newer with CEC support
for it to work… my 55 in tv will turn off, but not on… (so much for standards!), and only from the pi4… nothing else.

this is the screen library in NewPIR
https://github.com/bugsounet/screen

use the same 4 commands

and the matching code

    switch (this.config.mode) {
      case 1:
        if (set) exec("/usr/bin/vcgencmd display_power 1")
        else exec("/usr/bin/vcgencmd display_power 0")
        break
      case 2:
        if (set) exec("DISPLAY=:0 xset dpms force on")
        else exec("DISPLAY=:0 xset dpms force off")
        break
      case 3:
        if (set) exec("tvservice -p && sudo chvt 6 && sudo chvt 7")
        else exec("tvservice -o")
        break
      case 4:
        if (set) exec("echo 'on 0' | cec-client -s")
        else exec("echo 'standby 0' | cec-client -s")
        break
      case 5:
        if (set) exec("xset dpms force on")
        else exec("xset dpms force off")
        break
    }

[c1olli]

I use a mini pir sensor like this:
https://www.ebay.de/itm/133654306312
That switches the monitor directy completely off without any programming.
That solution works on my MagicMirror since one year without any problems.

[cowboysdude]

@mdlefevere No real answer for this… I’ve tried several times. I can turn it off but not back on…

Are you running a pi4 or pi3?

This was my answer to the pi3 and it works… cannot figure out the pi4

https://github.com/cowboysdude/Pir-Sensor

[MDLefevere]

@c1olli

That might be nice.
But how about the startup?. Do you get the ugly brand boot screen first?. How longt to fire up?

[MDLefevere]

@cowboysdude
@sdetweil

I’m running a 8GB PI4.
I’ve installed NewPIR and configured it like this:

		{
			module: 'MMM-NewPIR',
			position: 'top_left',
			configDeepMerge: true,
			config: {
				screen: {
					delay: 20000,
					turnOffDisplay: true,
					mode: 1,
						},
				pir: {
					gpio: 17
				}, 
			}
		},

Strange enough it’s working now on another monitor. No sleepy “No Signal” text on screen but just a monitor turning in stand-by.
It’s not a new monitor --> Fujitsu L20T-4 connected with DVI

I can’t get my hands on it…

[sdetweil]

@mdlefevere that monitor is not energy star compliant.

the monitor doesn’t actually turn off, but enters some lower power mode. or they turn off backlight.

[MDLefevere]

@sdetweil

Ah i see.
But on the other hand: It goes into stand-by so the front light turns orange, and the screen goes all black (no backlight).

[sdetweil]

@mdlefevere yes… getting harder and harder to find monitors that do this…
none of mine do.

[MDLefevere]

@sdetweil

So. I came home after work frustrated that it didn’t work.
After connecting another HDMI cable everything is working as expected 🙄.

I had a MicroHDMI to HDMI convertor and a HDMI cable after that.

I ordered a Micro to HDMI so i could get rid of the convertor.

Strange enough it is working with the convertor cable.

[sdetweil]

@mdlefevere never a dull moment!
so not all cables are the same…