Help please!!

sdetweil

@innovation ok, then do these two commands

ip link show
iwconfig

show the results

mine look like this

sam@galliumos:~/MagicMirror/modules/uploadPics$ ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
9: wlp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DORMANT group default qlen 1000
    link/ether a4:c4:94:66:7e:b1 brd ff:ff:ff:ff:ff:ff
sam@galliumos:~/MagicMirror/modules/uploadPics$ iwconfig
wlp1s0    IEEE 802.11  ESSID:"fubar"  
          Mode:Managed  Frequency:5.745 GHz  Access Point: 24:05:88:41:B5:08   
          Bit Rate=650 Mb/s   Tx-Power=22 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Power Management:on
          Link Quality=70/70  Signal level=-34 dBm  
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:52   Missed beacon:0

lo        no wireless extensions.

innovation

This post is deleted!

innovation

@sdetweil
pi@smart:~/MagicMirror/modules/uploadPics $ ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
link/ether b8:27:eb:9b:20:c3 brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DORMANT group default qlen 1000
link/ether b8:27:eb:ce:75:96 brd ff:ff:ff:ff:ff:ff
pi@smart:~/MagicMirror/modules/uploadPics $ iwconfig
eth0 no wireless extensions.

lo no wireless extensions.

wlan0 IEEE 802.11 ESSID:“ssk3”
Mode:Managed Frequency:2.422 GHz Access Point: CC:32:E5:E9:02:27
Bit Rate=24 Mb/s Tx-Power=31 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Power Management:on
Link Quality=42/70 Signal level=-68 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:10 Invalid misc:0 Missed beacon:0

pi@smart:~/MagicMirror/modules/uploadPics $

sdetweil

@innovation ok,

postinstall should be 43 lines long
if so do this

./postinstall

the check for qrcp.json again

innovation

@sdetweil Yes the file is there now

pi@smart:~/MagicMirror/modules/uploadPics $ ls qrcp.json
qrcp.json

sdetweil

@innovation ok, start mm

innovation

@sdetweil I am getting the same “default message if none supplied in the config.js”

sdetweil

@innovation weird

ok, add
debug: true,

to the module definition
and then do

npm start >somefile
once mm comes up u can stop it and then we can look at somefile

innovation

@sdetweil npm start >somefile
npm ERR! missing script: start

npm ERR! A complete log of this run can be found in:
npm ERR! /home/pi/.npm/_logs/2021-03-26T16_26_09_848Z-debug.log

Yes, the program started then I ended it

sdetweil

@innovation from the magicmirror folder please