MMM-Universal-PIR - ‘GPIOcommand exited with error!'

smegbadger

Hi

With no warning (I haven’t carried out any updates) MMM-Universal-Pir is now failing. It shows under the ‘PIR SENSOR’ heading on the MM screen ‘gpioCommand exited with error!’

Config is:

                    module: "MMM-Universal-Pir",
                        position: "bottom_right",
                        config: {
                            gpioCommand: "gpiomon -r -b gpiochip0 23",
                            onCommand: "wlr-randr --output HDMI-A-1 --on --transform 90",
                            offCommand: "wlr-randr --output HDMI-A-1 --off",
                            deactivateDelay: 120 * 1000,
                            }

and in a terminal gpiomon -r -b gpiochip0 23 shows events when the PIR is triggered and

wlr-randr --output HDMI-A-1 --on --transform 90 and wlr-randr --output HDMI-A-1 --off still control the screen.

gpiomon is v1.6.3

What can have changed?

Steve

smegbadger

smegbadger

The Docker log shows
[2026-02-10 11:30:10.955] [ERROR] [MMM-Universal-Pir] stderr: gpiomon: invalid option -- 'r' gpiomon: try gpiomon --help

but gpiomon -r -b gpiochip0 23 works in a terminal when pasted from the config.js file, very strange

It’s just stopped working!

Steve

smegbadger

magicm@magicmirror:/opt/mm/mounts/config $ gpiomon --help
Usage: gpiomon [OPTIONS] <chip name/number> <offset 1> <offset 2> ...

Wait for events on GPIO lines and print them to standard output

Options:
  -h, --help:           display this message and exit
  -v, --version:        display the version and exit
  -l, --active-low:     set the line active state to low
  -B, --bias=[as-is|disable|pull-down|pull-up] (defaults to 'as-is'):
                set the line bias
  -n, --num-events=NUM: exit after processing NUM events
  -s, --silent:         don't print event info
  -r, --rising-edge:    only process rising edge events
  -f, --falling-edge:   only process falling edge events
  -b, --line-buffered:  set standard output as line buffered
  -F, --format=FMT      specify custom output format

Biases:
  as-is:        leave bias unchanged
  disable:      disable bias
  pull-up:      enable pull-up
  pull-down:    enable pull-down

Format specifiers:
  %o:  GPIO line offset
  %e:  event type (0 - falling edge, 1 rising edge)
  %s:  seconds part of the event timestamp
  %n:  nanoseconds part of the event timestamp
magicm@magicmirror:/opt/mm/mounts/config $ gpiomon -v
gpiomon (libgpiod) v1.6.3
Copyright (C) 2017-2018 Bartosz Golaszewski
License: LGPLv2.1
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law.

-r is listed in the library help for v1.6.3

karsten13

@smegbadger

I had no idea about that, but now that you’re using Docker:

The gpiomon command is called inside the container (doesn’t work) and you call it for testing on the host (does work).

So I assume you have the newer version of gpiomon running in the container. So update the command in config.js to the new syntax described in the module README and try again (the new command will fail on the host but should work from inside the container).