Read the statement by Michael Teeuw here.
MMM-xiaomi - Temperature and Humidity from your smarthome
-
@smotx said in MMM-xiaomi - Temperature and Humidity from your smarthome:
hi,
Same problem here too
I have changed my router, so i have change wifi of Xiaomi hub
On magicmirror config i have set new ip 192.168.2.xxx (before 192.168.1.xxx).
But always nothing on MagicMirror after reboot.
perhaps token has changed with new router… So, on the rasp i launch command ```
miio discover` $ sudo miio discover INFO Discovering devices. Press Ctrl+C to stop. Device ID: 567xxxx54 Model info: Unknown Address: 192.168.2.xxx Token: ??? Support: Unknown ` Anybody know why ? :(.I had the same problem. Meanwhile, I have found the solution. An update from Xiaomi changed the token in the gateway. This must now be read out via the smartphone. In my case the miio discovery command did not work any more. I followed this instruktion to get the new token
… and now all works fine again - I have all my sensors back on the mirror.
regards
Mike -
after this command :
miio tokens update 567xxxxx --token 6xxxxxxxxxxxxxxxxxxxxxxxxxxxmine to work again a few days, and now is KO again… for the third time… :face_with_steam_from_nose: Token has not changed, ip has not changed…
-
I can’t find what needs to be changed in CSS to change the font color of the temperature and humidity numbers.
-
Hi guys,
I have two temperature sensors. Each sensor registers with a gateway. Could anyone tell me how to add the two gateways in config.js file?
I try to add the following codes in config.js:
{
module: ‘MMM-xiaomi’,
position: ‘top_right’,
header: ‘Temperature / Humidity’,
config: {
gatewayIP: ‘192.168.186.181’,
gatewayToken: ‘xxxxxxxx-ceec093b30b1775dc741a7’,
showWindow: true,
showVentilation: true,
showLights: false,
audioNotifications: true,
rooms: [
{
name: ‘Bedroom’,
sortOrder: 20,
devices : [‘158d000xxxx9f’]
}
],
gatewayIP: ‘192.168.186.166’,
gatewayToken: ‘xxxxxxxx–927e2d20b22c22b007194c’,
rooms: [
{
name: ‘Childroom’,
sortOrder: 30,
devices : [‘158d000xxxx4f6’]
}
]
}
}but MagicMirror always display the last sensor, which registers with the secondary gateway in config.js file.
Could anyone give me some suggestions? Thanks in advance!
-
@lovesicker Hi,
I think you are on the wrong way: You use gatewayIP and gatewayToken twice. Thats not necessary.
Look to my configuration - this works fine:
{
module: ‘MMM-xiaomi’,
position: ‘bottom_left’,
colored: true,
header: ‘Temperatur / Luftfeuchtigkeit’, // This is optional
config: {
gatewayIP: ‘192.168.160.xx’,
outsideSensorId: ‘15xxx0201dxxx’,
gatewayToken: ‘cd857eee1fc760d029767709cd50xxxx’,
showWindow: true,
showVentilation: true,
showLights: false,
showTend: false,
showNotifications: false,
audioNotifications: false,rooms: [ { name: 'Büro', minTemperature : 15, maxTemperature : 35, sortOrder: 1, devices : ['158d0001c2cxxx'] }, { name: 'Aussentemperatur ', sortOrder: 20, devices : ['15xxx00201d4xxx'] }, { name: 'Wohnzimmer ', minTemperature : 15, maxTemperature : 35, sortOrder: 2, devices : ['158d0001c2cxxx'] }, { name: 'Schlafzimmer ', sortOrder: 3, minTemperature : 15, maxTemperature : 30, devices : ['1xxx000201dxxx', '15xxx001f49xxx'] }, { name: 'Philipp', minTemperature : 15, maxTemperature : 35, sortOrder: 4, devices : ['1xxd0001c14xxx'] }, { name: 'Marco', minTemperature : 15, maxTemperature : 35, sortOrder: 5, devices : ['15xxx01f54xxx'] }, { name: 'HW-Raum', minTemperature : 10, maxTemperature : 35, sortOrder: 7, devices : ['15xxx002029xxx'] }, { name: 'Garage', minTemperature : 15, maxTemperature : 35, sortOrder: 10, devices : ['15xxx001c1xxx'] }, { name: 'Keller', minTemperature : 15, maxTemperature : 35, sortOrder: 9, devices : ['15xxx001c2axxx'] }, { name: 'WC', minTemperature : 15, maxTemperature : 35, sortOrder: 8, devices : ['15xxx001c1axxx'] }, { name: 'Bad', minTemperature : 18, maxTemperature : 35, sortOrder: 6, devices : ['15xxx001c2cxxx'] },]
-
@garbleflux First, thank you for your reply.
I have two different rooms. There are a temperature sensor and a gateway in each room! So I have to add two gateways in config.js file. -
@lovesicker Hi,
why do you use two gateways? It’s not necessary. I use one gateway for my complete house. I use 10 temperature and humity sensors. Have a closer look to my config.
Regards Mike. -
@garbleflux thank you for your discussion.
It’s difficult to explain. Let me try. Maybe my scenario is very different with yours.
There are one Xiaomi temperature sensor, one Xiaomi air conditioning companion (gateway) and one Xiaomi intelligent clock (integrated partial AI function) in EACH bedroom.
When I speak to the clock, “Hi Xiaoai, please tell me the room temperature” or “temperature”, the clock tell me the correct number of degrees via the RIGHT gateway. When I say “power on the air conditioning”, the same thing happen.
It’s unsuitable that I say "tell me CHILDROOM temperature " or “power off CHILDROOM air conditioning” when I’m in my bedroom. Although I know it is realizable.
I’m not sure I clearly explain the reason. Anyway, I need two gateways in my house.
-
@lovesicker OK. Did you try to start the module twice? Maybe this is the possibility to activate both gateways at the same time as you need it.
Regards Mike -
Yes, I can add two instances in config.js file at the same time.
YOU ARE RIGHT!
It’s not necessary. According to your suggestion, I register all of my sensors on ONE gateway. I can still fulfill all my needs.I’m stupid. I’ve made simple things complicated.
Tanks again!
Good luck.
