I have made an updated extended version of MMM-cryptocurrency it is based on Mattelo’s work

MMM-crypto-portfolio

I am not using Vera, but checked what is possible

http://wiki.mios.com/index.php/Luup_Control#Getting_the_list_of_UPnP_devices_you_can_control

What you could do is put a 10k Resistor between GPIO 22 and GND. if the PIR disconnects your PIN is pulled LOW.

PIRs may give different signals my PIR only gives a high (3v3)

You could try to use a pull-up resistor maybe the PIR output is 5V

pullup resistor

Check this website. Otherwise your PIR is broken. If you are in the Netherlands i can post by snailmail another one to you that works for sure,

As I wrote in my previous message check if the GPIO is low when you disconnect the PIR
I always check all parts with an Arduino Nano or Uno to see if it works and if it needs settings it is easily done before installing.
This evening I will not be online any much longer.

Maybe your PIR is always HIGH
thats is why you should check with a resistor if it works.
Or disconnect the OUT pin to see in the screen stays off.

Hello Peter,

There are two different things. One is Domoticz and the other is MagicMirror.
The module requests data from Domoticz. It is a reply in json.
This comes from my shutter.

{
         "AddjMulti" : 1.0,
         "AddjMulti2" : 1.0,
         "AddjValue" : 0.0,
         "AddjValue2" : 0.0,
         "BatteryLevel" : 255,
         "CustomImage" : 0,
         "Data" : "Open",
         "Description" : "",
         "DimmerType" : "abs",
         "Favorite" : 0,
         "HardwareID" : 7,
         "HardwareName" : "ZwaveUSB",
         "HardwareType" : "OpenZWave USB",
         "HardwareTypeVal" : 21,
         "HaveDimmer" : true,
         "HaveGroupCmd" : true,
         "HaveTimeout" : false,
         "ID" : "00000501",
         "Image" : "Light",
         "IsSubDevice" : false,
         "LastUpdate" : "2018-04-16 08:37:09",
         "Level" : 255,
         "LevelInt" : 255,
         "MaxDimLevel" : 100,
         "Name" : "Rolluik",
         "Notifications" : "false",
         "PlanID" : "7",
         "PlanIDs" : [ 7 ],
         "Protected" : false,
         "ShowNotifications" : true,
         "SignalLevel" : "-",
         "Status" : "Open",
         "StrParam1" : "",
         "StrParam2" : "",
         "SubType" : "Switch",
         "SwitchType" : "Blinds Inverted",
         "SwitchTypeVal" : 6,
         "Timers" : "true",
         "Type" : "Light/Switch",
         "TypeImg" : "blinds",
         "Unit" : 1,
         "Used" : 1,
         "UsedByCamera" : false,
         "XOffset" : "698",
         "YOffset" : "1168",
         "idx" : "31"
      },

The Image in this record is not the image in the MagicMirror. The MagicMirror Icons are from Fontawesome version 4.7 there is now a version 5 available but doesn’t like to work along 4.7 in MagicMirror.

The icons you see in my module are based on the type of device retrieved with the json file from Domoticz. See the lines in my code from 55 to line 71

There are no icons for shutters/shades or similar in fontawesome. That is why I use the status text from Domoticz. (In the Netherlands the webinterface is in Dutch but you will see that the status of the blinds are in English)

Hope this clarifies the icon issue.

You could try if you are using the right GPIO by pulling the pin Up.

Take a 10k Resistor one side on 5V and the other side tap the GPIO pin that is what the PIR would do. Then you can check if you use the proper pin.

I have added colour yellow to closed Blinds/shutters.
There is no added colour to lights, outlets because the are not visible when they are inactive.
However if you like to add a colour you can change the code in line 72
make sure you have a space between small and yellow just before the i-element for the icons

@Peter What colours would you like and for what state (On, Off, Open Close)