@Mar Hey, I’m not sure, if I can give you a proper report on the performance, I’ve got no experience with other raspi models and I’m still in the stage of building the software part.

I can tell you though that the installation won’t be painless, there’s some stuff that needs manual updating. If you decide to go through with it and run into problems, hit me up, maybe I could help you out.

@bhepler That’s what I had concluded as well.

There’s already the wordnik module , I’ve looked into its code, couldn’t find out how to edit it for my usage though, since my coding knowledge is very limited.

Maybe the bible verse module? I’ll give it a go.

@Mar Hey, I’m not sure, if I can give you a proper report on the performance, I’ve got no experience with other raspi models and I’m still in the stage of building the software part.

I can tell you though that the installation won’t be painless, there’s some stuff that needs manual updating. If you decide to go through with it and run into problems, hit me up, maybe I could help you out.

@bhepler That’s what I had concluded as well.

There’s already the wordnik module , I’ve looked into its code, couldn’t find out how to edit it for my usage though, since my coding knowledge is very limited.

Maybe the bible verse module? I’ll give it a go.

hi,

I’m trying to get an RSS feed going that would show more than just the RSS title, unfortunately I’m not sure on what to change (and where) to get more lines in the feed (not just title)

I’ve tried MMM-RSS-FEED and adjusting the default newsfeed module, but am still struggling

Example:
http://feeds.feedblitz.com/german-word-of-the-day

content of the feed:

vulgäre Ausdrücke: profanity
 2017-01-15 00:00 UTC

Part of speech:	noun
Example sentence:	Man sollte hier keine vulgären Ausdrücke benutzen.
Sentence meaning:	One shouldn't use profanity here.

What MMM-RSS-FEED module shows:

vulgäre Ausdrücke: profanity

What newsfeed module shows:

relevant config.js part:

{
module: 'newsfeed',
position: 'top_right',
config: {
feeds: [
{
title: "German word of the day:",
url: "http://feeds.feedblitz.com/german-word-of-the-day&x=1"
}
],
showSourceTitle: true,
showPublishDate: true,
showDescription: true
}
},

Is there a way to force either of the modules to display the RSS body (description) formatting properly? Respect new lines and tabs?

Well, clean installation fixed the issue, not sure what the root cause was though.

@creye There isn’t any difference, even with an actual monitor it looks like this. I’ve just been using VNC, since it’s more convenient in my setup.

Anyway, after backip up the current state, I’m starting over with a fresh Jessie Lite installation, let’s see how that goes.

Hi everybody,

I’m running a Pi Zero with NOOBS installation and am having trouble getting a browser use the full resolution available - 1080x1920 (vertical fullHD monitor).

When booting up to GUI, everything works properly, whole screen is used. Changing boot to console (autologin) and just starting midori, I get to this:

https://i.imgur.com/5NwBX5l.png

Overscan settings in config.txt did not have any influence, I’ve tried several different settings in config.txt (which I unfortunately did not write down), what would you suggest?

Thank you for your help!

Below are the contents of relevant config files.

---

/boot/config.txt:

# For more options and information see
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
framebuffer_width=1080
framebuffer_height=1920
framebuffer_depth=32
framebuffer_ignore_alpha=1

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on
^M
# NOOBS Auto-generated Settings:^M
hdmi_force_hotplug=1^M

/home/pi/start.sh (launched on startup by editing .bashrc):

cd ~/MagicMirror
node serveronly &
sleep 30
#sudo xinit /usr/bin/kweb -KJERLH http://localhost:8080
sudo xinit /home/pi/startMidori.sh

/home/pi/startMidori.sh:

#!/bin/sh
xset -dpms # disable DPMS (Energy Star) features.
xset s off # disable screen saver
xset s noblank # don’t blank the video device
matchbox-window-manager &
#midori -e Fullscreen -a http://localhost:808
midori -e Fullscreen -a http://www.reddit.com