I do this in first and i retry now but it’s always display “loading sensor data”, then i modify sensorPin: 20,in the MMM-DHT-Sensor.js because it stayed code_sensorPin: 20, but the problem stay here…
I even connected DHT22 directly to my raspi (GND in pin 6 and VCC in pin 4)
it’s annoying because it sounds simple …

my DHT22 would it be broken, how to know it …

My MMM-DHT-Sensor.js :

Module.register("MMM-DHT-Sensor", {

	defaults: {
		updateInterval: 60 * 60 * 1000, // Every hour.
		initialLoadDelay: 0, // No delay/
		animationSpeed: 1000, // One second.
		units: config.units, // Celsius
		relativeScale: 30,
		debug: false,
		sensorPin: 2,
		sensorType: 22

My config.js :

	{
	module: "MMM-DHT-Sensor",
	position: "top_right",
	header: "Upstairs",
	config: {
		sensorPin: 2,
		sensorType: 22,
		updateInterval: 60 * 60 * 1000,
		initialLoadDelay: 0,
		animationSpeed: 1000,
		units: "metric",
		relativeScale: 35,
		debug: false
	}
},

thank you for the info, it worked with MMM-DHT-Sensor by plugging it into the GPIO 2 as a prerequisite then rebooting it does not work anymore it displays all the time “loading sensor data”

Hello,
I am blocked at node auth_and_test.js, indeed when I type this command here is what is displayed :

So I can’t Copy the code and paste in my console’s request

where do I make a mistake?
Thank you for your help.

Hello,
I just installed the MMM-DHT22 module
here is my installation with a RasberryPi and DTH 22 (not 11) :

I modified in my config.js and in MMM-DTH22.js: sensorPIN: 20,,
but the temperature is displayed in Undefined and I have nothing in humidity. I tried with sensorPIN: 38, while leaving my DTH22 connected to GPIO 20 but that does not change anything.
Thank you for your help.

I tried to edit my 1st post but I can’t: “You are only allowed to edit posts for 3600 second (s) after posting”.

in the case I published which is:

**** Liste des Périphériques Matériels CAPTURE ****
carte 1: USB [WordForum USB], périphérique 0: USB Audio [USB Audio]
  Sous-périphériques: 1/1
  Sous-périphérique #0: subdevice #0
pi@raspberrypi:~ $ aplay -l
**** Liste des Périphériques Matériels PLAYBACK ****
carte 0: b1 [bcm2835 HDMI 1], périphérique 0: bcm2835 HDMI 1 [bcm2835 HDMI 1]
  Sous-périphériques: 4/4
  Sous-périphérique #0: subdevice #0
  Sous-périphérique #1: subdevice #1
  Sous-périphérique #2: subdevice #2
  Sous-périphérique #3: subdevice #3
carte 2: Headphones [bcm2835 Headphones], périphérique 0: bcm2835 Headphones [bcm2835 Headphones]
  Sous-périphériques: 4/4
  Sous-périphérique #0: subdevice #0
  Sous-périphérique #1: subdevice #1
  Sous-périphérique #2: subdevice #2
  Sous-périphérique #3: subdevice #3
pi@raspberrypi:~ $ 

my mic in on card 1, device 0 because " Liste des Périphériques Matériels CAPTURE", and my 3.5 jack headphone is on card 2, device 0 because " Liste des Périphériques Matériels PLAYBACK" , and in card 0, device 0 it’s HDMI.

is it correct ?

Great, thank you !
So can you confirm me the card and device for my mic and headphones ?

@Bugsounet TOUTES MES PLATES EXCUSES !!! J’avais donc mal compris, vraiment désolé…
I continue in English because it is required here (and that you will understand that I all pages and tutorials read with google translate …):
But then why in the page of your MMM-GoogleAssistant there is only the link git@github.com: bugsounet / MMM-GoogleAssistant.git and not all the description to install MMM-GoogleAssistant ?