MMM-MyHomeWizard

[htilburgs]

@sdetweil In the netherlands, we do have that!
Fortunately, otherwise I would not have been able to write this MagicMirror module ;-)

[htilburgs]

Update to v2.0.0

In this updated version, the data is saved daily at 11:59 p.m. This makes it possible to see the current difference during a day.
You can enable and disable this option via the showDeltaXXXX options in config.js.

Module page: MMM-MyHomeWizard

[vansman]

I installed the module and edit the config file including the ip adressen from the P1 and the watermeter.
When i start MagicMirror is see de header Homewizard but it says Loading…
Any suggetions what this could be?

[htilburgs]

@vansman
Good morning. This can be a lot of things. You provided no info.
Can you pleaase post your config (without any personal info)
When you start MM with PM2, than please stop it.
Go to ~/MagicMirror folder and start npm start dev and look if there are any errors.

[vansman]

@htilburgs Good day, I don’t start MM with PM2 .

This is a part in of my config.js

{
		module: "MMM-DHT-Sensor",
		position: "bottom_right",
		header: "Badkamer temperatuur",
		config: {
			sensorPin: 4,
    	sensorType: 11, // 11 for DHT11 or 22 for DHT22 / AM2302
    	updateInterval: 60000, //milliseconden
    	
		}
  },
  
	
	{
  module: 'MMM-MyHomeWizard',
  position: 'right',
  header: 'HomeWizard',
  disabled: false,
  config: {
		P1_IP: "192.168.178.152",	    // IP Address HomeWizard P1 meter
		WM_IP: "192.168.101.14",	    // IP Address HomeWizrd Water meter - Remove when not used
		extraInfo: true, 	    // Show extra information from P1 meter
		currentPower: true,	// Show the current Power Consumption
		currentWater: true,	// Show the current Water Consumption
		showGas: true,		    // Show the Gas option
		showFooter: true,	    // Show footer (name Power Meter)
		updateInterval: 5000,   // Update every 5 seconds
		maxWidth: "500px",	    // Max Module width
        showLastUpdate: true,	// Show the last update for the History Data in the footer
        showDeltaPower: true,	// Show Delta between History and Current data (Power)
        showDeltaGas: true,		// Show Delta between History and Current data (Gas)
        showDeltaWater: true	// Show Delta between History and Current data (Water)
  		}
},
    
  
  {
  module: 'MMM-Pir',
  position: 'top_center',

When i run npm start dev and filter on myhomewizard i see no errors,

Load script: modules/MMM-MyHomeWizard/MMM-MyHomeWizard.js
module.js:483 Module registered: MMM-MyHomeWizard
loader.js:137 Bootstrapping module: MMM-MyHomeWizard
loader.js:141 Scripts loaded for: MMM-MyHomeWizard
loader.js:179 Load stylesheet: modules/MMM-MyHomeWizard/MMM-MyHomeWizard.css
loader.js:144 Styles loaded for: MMM-MyHomeWizard
translator.js:103 MMM-MyHomeWizard - Load translation: translations/nl.json
loader.js:147 Translations loaded for: MMM-MyHomeWizard
MMM-MyHomeWizard.js:38 Starting module: MMM-MyHomeWizard

Thanks

[htilburgs]

@vansman
The first thing I see in your configuration is

position: 'right'

As far as I know, that doesn’t work in MagicMirror and you should get an error when you’re loading MagicMirror.

[2026-02-17 18:10:22.072] [WARN]  [check_config] Module 5 ("MMM-MyHomeWizard") uses unknown position: "right" 
[2026-02-17 18:10:22.073] [WARN]  [check_config] Known positions are: fullscreen_below, top_bar, top_left, top_center, top_right, upper_third, middle_center, lower_third, bottom_bar, bottom_left, bottom_center, bottom_right, fullscreen_above 

Can you change this to top_right and try what does happens?

Checking your IP Addresses:
You can check if your IP Addresses give information. Put in the next URL in a browser. If the IP Address is correct, you should get something like:

P1 Meter: http://192.168.178.152/api/v1/data/
Water: http://192.168.101.14/api/v1/data/

Result:

  "wifi_ssid": "WiFi Network Name",
  "wifi_strength": 100,
  "smr_version": 50,
  "meter_model": "Sagemcom T210-D ESMR5.0",
  "unique_id": "ID",
  "active_tariff": 2,
  "total_power_import_kwh": 18833.243,
  "total_power_import_t1_kwh": 10804.883,
  "total_power_import_t2_kwh": 8028.36,
  "total_power_export_kwh": 0.166,
  "total_power_export_t1_kwh": 0.166,
  "total_power_export_t2_kwh": 0,
  "active_power_w": 398,
  "active_power_l1_w": 257,
  "active_power_l2_w": 27,
  "active_power_l3_w": 113,
  "active_voltage_l1_v": 230,
  "active_voltage_l2_v": 231,
  "active_voltage_l3_v": 230,
  "active_current_a": 1.726,
  "active_current_l1_a": 1.117,
  "active_current_l2_a": 0.117,
  "active_current_l3_a": 0.491,
  "voltage_sag_l1_count": 4,
  "voltage_sag_l2_count": 4,
  "voltage_sag_l3_count": 4,
  "voltage_swell_l1_count": 0,
  "voltage_swell_l2_count": 0,
  "voltage_swell_l3_count": 0,
  "any_power_fail_count": 54,
  "long_power_fail_count": 9,
  "total_gas_m3": 5595.841,
  "gas_timestamp": 260217182000,
  "gas_unique_id": "ID",
  "external": [
    {
      "unique_id": "ID",
      "type": "gas_meter",
      "timestamp": 260217182000,
      "value": 5595.841,
      "unit": "m3"
    }
  ]
}

{
  "wifi_ssid": "WiFi Network Name",
  "wifi_strength": 86,
  "total_liter_m3": 19.652,
  "active_liter_lpm": 0,
  "total_liter_offset_m3": 0
}

[MZ-BER]

@htilburgs - can you please tell me how do you measure your gas consumption? Do you use any device that monitor the Gas counter?

[htilburgs]

@MZ-BER
It is measured with the P1 meter.
It does both.

[vansman]

@htilburgs Api is working. Actually i am using an older version of mmm.homewizard wich is working. I see that your version can provide more data including the watermeter. When i use config file below is see the data from mmm.homewizard but mmm.myhomewizard gives Header plus Loading…
I changed the position to bottom_right but that doesn’t have effect. For the older version i use only right wich works in my config .

,
  
  
        {
                module: "MMM-HomeWizard",
                position: "right",
                header: "Electricity & Gas",
                config: {
                        url: "http://192.168.178.152/api/v1/data",
                        updateInterval: 2000
                }
        },
	
	{
  module: 'MMM-MyHomeWizard',
  position: 'bottom_right',
  header: 'HomeWizard',
  disabled: false,
  config: {
		P1_IP: "192.168.178.152",	    // IP Address HomeWizard P1 meter
		WM_IP: "192.168.101.14",	    // IP Address HomeWizrd Water meter - Remove when not used
		extraInfo: true, 	    // Show extra information from P1 meter
		currentPower: true,	// Show the current Power Consumption
		currentWater: true,	// Show the current Water Consumption
		showGas: true,		    // Show the Gas option
		showFooter: true,	    // Show footer (name Power Meter)
		updateInterval: 5000,   // Update every 5 seconds
		maxWidth: "500px",	    // Max Module width
        showLastUpdate: true,	// Show the last update for the History Data in the footer
        showDeltaPower: true,	// Show Delta between History and Current data (Power)
        showDeltaGas: true,		// Show Delta between History and Current data (Gas)
        showDeltaWater: true	// Show Delta between History and Current data (Water)
  		}
},
    
  
  {

I tried also 192.168.178.152/api/v1/data but that doesn’t work also.

[htilburgs]

@vansman
In the Homewizard app on your phone, you have to activatie the use of local api. What I think is strange is that when you go to

http://192.168.178.152/api/v1/data

that you don’t get any data. This mechanisme is the same as in MMM-Homewizard (see the config for your first app)

Activating Local API
Go to Settings > Meters > ‘‘Your meter’’, and enable Local API for the P1 Meter and/or the Water Meter at the botom of the page.

The same for the Watermeter. If they are off, they don’t work.