[Electron] display en screen after installing MMM-PIR-Sensor

[sdetweil]

@RIKKO14 and u don’t need to reboot. just use the pm2 commands

pm2 restart 0

[RIKKO14]

I do this, MM reload but now after 2-3 secondes the screen turn off, GA with Jarvis works in background but i can’t find the screen of MM, if i do Ctrl + M
nothing is happening, there, I’m completely stuck…, I unplugged but the problem stay here…

[sdetweil]

@RIKKO14 is the screen actually powered off? did u enable ssh to get into a terminal window if desktop/mm has trouble?

if so I can issue commands there to turn on display tvservice or dpms…

I don’t use PIR, lots of troubles.

[RIKKO14]

I dont use ssh, only command on the py.
Instead of that, i think the py cut the power to the screen because the led of my screen is yellow like power off and not blue like something displayed.

[RIKKO14]

Yes, the screen actually powered off

[RIKKO14]

And I forgot to not the IP adress of my py, so I can’t use ssh now…
Pffff, I’m not lucky, every modules I want works instead of the PIR module…

[RIKKO14]

If i find my IP adress, Can you give me the commands to delete the problem ?

[sdetweil]

@RIKKO14 if u didn’t turn on ssh, it isn’t on, so can’t use it anyhow. look in your router to see what addresses were given out…

I do that quite often, then fix/reserve the address so I don’t have to remember

[RIKKO14]

ok, i find my IP adress (I’ve wrote it in excel file with some commandes i use) and I connected in SHH with putty,
thanks for your help to delete the commandh whose powered off my screen

[RIKKO14]

below my pm2 logs,
If that can help you…
https://www.cjoint.com/c/JHvqsqJ1QTT

[RIKKO14]

If it can help you this is my pm2 logs : https://www.cjoint.com/c/JHvqsqJ1QTT

[sdetweil]

@RIKKO14 looking at… hard to tell
do

pm2 stop 0
pm2 flush 
pm2 start 0

the will throw away the old logs…

[RIKKO14]

I do this, the problem still here…

[sdetweil]

@RIKKO14 it just makes the log easier to read. please post it again

[RIKKO14]

hre it is :
https://www.cjoint.com/c/JHvrPBCBgZT

[RIKKO14]

and this one (because i don’t if it it change something) : https://www.cjoint.com/c/JHvrUegIVzT after the command :

pm2 stop 0
pm2 flush 
pm2 start 0

and after only pm2 logs --lines=100

without pm2 status and pm2 stop 0

[sdetweil]

@RIKKO14 i see this
0|mm | [2020-08-21 19:37:58.395] [LOG] [LPCM16] WARN: arecord: pcm_read
:2145: erreur en lecture: Appel système interrompu
and this
0|mm | [2020-08-21 19:43:41.435] [LOG] [Error: failed to read sensor]

so we may have to look at t he browser dev window,
ctrl-shift-i on the mirror keyboard
select the tab labebled console,
and scroll up to see any errors, usually in red text

[RIKKO14]

ctrl+shift+i on the mirror keyboard : nothing displayed
ctrl+shift+i on my pc keyboard : this is displayed :

[RIKKO14]

ctrl+shift+i on the mirror keyboard : nothing displayed : because my screen is powered off : source of the issue…

[sdetweil]

@RIKKO14 too small to read