Apply color to future events in CalendarExt3

[sdetweil]

@kkmirr04 ok,

1st does the default cal show color on the events in the list per the URL configs?

the config you presented will show ALL the events together, intertwined. in a single list

EXT3 could see them differently by name

can you show the ext3 configs
please, always use the code block wrapper around config or logs)

to do in this message editor

paste the text you want to present
blank line above and below
select the text you just pasted
hit the code block button </> in the menu above the editor

[kkmirr04]

@sdetweil
I do have color on the events list - hopefully this is what you were asking for

I would love to have it broken back out into two separate lists, but when I do that and integrate MMM-Pages, it refuses to load the second calendar stream on the events list and also into the calendar. Its like it just refuses to go out and check.
I think its a limitation of the Pages module, I’ve got it setup for the classes configuration. You can call the same module on different pages, but it doesn’t seem like I can call the default calendar module twice on the same page. I haven’t done much research on the Pages issue, thats my next one to tackle.

Interestingly, looking at the CalendarExt3 view today - none of the future events have color applied to them:

Think I got the code block correct this time - thanks for pointing that out to me.

{
      module: "MMM-CalendarExt3",
      classes: "page1",
      position: "bottom_bar",
      title: "",
      config: {
        mode: "week",
        instanceId: "main",
	showWeekNumber: false, 
	//useSymbol: true,
	//displayLegend: true,
        maxEventLines: 10,
	//useWeather: true,
        firstDayOfWeek: 0,
        calendarSet: ['xx_cal', 'yy_cal'],
        
      }
    },

[sdetweil]

@kkmirr04 ok, there is a quirk in the EXT3 family of modules .

They don’t know when the messages are coming. And don’t want to flash the screen with changes each time they arrive.
Some events of today from cal 1 and more from cal 2 at a different time

So they use a refreshInterval default 15 minutes

But you don’t want to wait 15 mins for the first draw.
So they have another setting waitFetch:5 seconds

After startup wait waitFetch time and draw whatever events have arrived. Even if none

THEN you have to wait refreshInterval time

You have both at default

A little downside on the waitFetch is you get NOTHING til it expires

[sdetweil]

Another question. When did you install ext3

You DID run npm install the that module folder right?

[kkmirr04]

@sdetweil

I believe ext3 was one of the first modules I installed when I started everything this weekend. I do remember having some errors so theres a good chance I messed something up. I just ran npm install again and it processed fine, but no changes on the functionality.

Would it make sense to delete out the folder and try downloading / configuring the module again?

[sdetweil]

@kkmirr04 no, there was a fix a couple weeks ago, but if you just loaded it, should be fine

Can you add waitFetch:20000,

To the EXT3 module config

[sdetweil]

@kkmirr04 can you try release 2.36 just released.

[kkmirr04]

I tried adding the waitFetch and updating and no changes on my end. Do you think doing a clean install might be the next best step?

[sdetweil]

@kkmirr04 can you show the default cal and ext3 on the same page. With the same events.

Can you remove the calendarSets from the ext3 config

npm install in the ext3 module folder is enough

[kkmirr04]

@sdetweil Here is the events with the calendar

Remove the calendar sets and then run npm install again? I did see there is an update for my NPM - should i do that update too?

I also just noticed theres an error with CalExt3 when I close MM

[sdetweil]

@kkmirr04 thanks. I will try to test this out in a little bit

No, ignore the npm message

Yes, we found a bug in MagicMirror when looking for module updates. No harm done

[sdetweil]

@kristjanesperanto

can you explain this? the default cal shows colored, but Ext3 does not

I can duplicate, text not colored in Ext3

but pop is all colored.

[sdetweil]

@kkmirr04 on your second cal instance not showing

can you show the config, xxx out the cal url…

I am using pages, with ext3 on diff and cal on diff without problem… (except for ext3 color)