I have sound! Thanks for all the help. What I did, after I read some the links provided, I decided to format another SD card and reload all my programs and I got sound. Then I compared the two SD card files and found that the original card had a file called AIY Project Voice, this program overwrote some of the files and change the parameters for output, apparently my grandson downloaded it thinking he was helping. Now all is good and I’ve learned a lot with every ones help. Thanks again.

I have sound! Thanks for all the help. What I did, after I read some the links provided, I decided to format another SD card and reload all my programs and I got sound. Then I compared the two SD card files and found that the original card had a file called AIY Project Voice, this program overwrote some of the files and change the parameters for output, apparently my grandson downloaded it thinking he was helping. Now all is good and I’ve learned a lot with every ones help. Thanks again.

My knowledge of this is very limited, I don’t understand where you want me to put the markdown at?

Ok, tried all three but no luck, not sure what to do next. Here’s a copy of my config file if that may help

For more options and information see

http://rpf.io/configtxt

Some settings may impact device functionality. See link above for details

uncomment if you get no picture on HDMI for a default “safe” mode

#hdmi_safe=1

uncomment this if your display has a black border of unused pixels visible

and your display can output without overscan

#disable_overscan=1

uncomment the following to adjust overscan. Use positive numbers if console

goes off screen, and negative if there is too much border

#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

uncomment to force a console size. By default it will be display’s size minus

overscan.

#framebuffer_width=1280
#framebuffer_height=720

uncomment if hdmi display is not detected and composite is being output

#hdmi_force_hotplug=1

uncomment to force a specific HDMI mode (this will force VGA)

#hdmi_group=1
#hdmi_mode=1

uncomment to force a HDMI mode rather than DVI. This can make audio work in

DMT (computer monitor) modes

#hdmi_drive=2

uncomment to increase signal to HDMI, if you have interference, blanking, or

no display

#config_hdmi_boost=4

uncomment for composite PAL

#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

Uncomment some or all of these to enable the optional hardware interfaces

#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

Uncomment this to enable the lirc-rpi module

#dtoverlay=lirc-rpi

Additional overlays and parameters are documented /boot/overlays/README

Enable audio (loads snd_bcm2835)

#dtparam=audio=on
[pi0]
dtoverlay=dwc2
[all]
start_x=1
gpu_mem=128
dtoverlay=googlevoicehat-soundcard
display_rotate=1

Sorry for the large font, not well verse with the editing portion of this forum.

I’ll follow the link and check it out, then I’ll let you know what I did. Thanks for the guidance.

@sdetweil No

I should have included in my first post, but I did attach a separate cable for sound to speakers, but that didn’t work so I tried earphones to make sure. Thanks for confirming that for me. Any other suggestions?

Thanks in advance. I’ve been searching the forum and have not found an solution for this. Currently I am running a Raspberry Pi 3 B. I have MM loaded and some modules loaded. I have a HDMI to DVI cable attached going to my monitor. Any help is appreciated.

Thanks,
Bill

Once again, thanks. I tried what you suggested and it worked (using Control R after the MM loads the module), however I plan on setting my MM up on a schedule to go off when I’m not at home so this is not practical for me. I also check out the link you provide about but dating my API key, when I use this key with the default weather module I get a 4 day forecast so I know it’s the most current one.

So I went on line and setup an account with DarkSky and it worked the first time and after multiple reboots, this is what I’m looking for, however, now I have a new issue, see pic below. Now N/A appars after the temp.

Sorry about the pic still learning some of the basics.

Sorry it took me so long to get back. Unable to mark this topic “solved.” The three vertical dots on the right only give me the option to “edit,” “delete’” and “Bookmark.”

Again thanks for your help.

Bill

Thanks for the reply! Here’s a copy of my config for the NOAA3 weather
{
module: ‘MMM-NOAA3’,
position: ‘top_right’,
config: {
provider: “openweather”, // From list above
apiKey: “xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx9”, // From one of the providers listed above
airKey: “xxxxxxxxxxxxxxxn”,
css: “NOAA4”,
userlat: “34.139”,
userlon: “-79.6879”,
updateInterval: 30 * 60 * 1000,
}
}

Again, thanks for your help!
Bill

forgot the coma after the userlon entry.