@paulb
Hi,

I used

sudo apt-get install unclutter

unclutter -idle 3

@velkrosmaak
I also use motion to detect and then stream the video via to the MM via MMM_SmartWebDisplay

In the motion config file (/etc/motion) search for

’ # Command to be executed when an event starts. (default: none)
'# An event starts at first motion detected after a period of no motion defined by event_gap
'# on_event_start value
'# Show iFrame in MagicMirror
on_event_start /etc/motion/notifyOn_MM.sh

'# Command to be executed when an event ends after a period of no motion
'# (default: none). The period of no motion is defined by option event_gap.
'# on_event_end value
'# Hide iFrame on MagicMirror
on_event_end /etc/motion/notifyOff_MM.sh

and the scripts could look like:

'# Show SmartWebDisplay in MagicMirror (iFrame no longer supported in MM 2.7.1)
curl --no-verbose http://:8080/remote?action=SHOW"&"module=module_10_MMM-SmartWebDisplay

Peter

@sdetweil
I finally got it working again!:thumbs_up:

I did a full fresh installation on a new SD card with complete latest Raspian and new MM and all the modules I used before…and still the same behavior: MMM-IFrame showed nothing and I got the same warnings as mentioned below.

Then I tried MMM-SmartWebDisplay by @AgP42 which finally displays my video stream again. (BTW: This also works with other URLs as described in the documentation)
Many thanks for this module.:clapping_hands:

For all having issues with MMM-iFrame, MMM-IFrame-Ping etc., try MMM-SmartWebDisplay.
Don’t forget to do a NPM install in the module folder once the module is cloned.

Thanks, Peter

@Achilles

I‘m using MMM-SmartWebdisplay
https://github.com/AgP42/MMM-SmartWebDisplay
to display a stream from my front door camera (simple USB-Camera connected to a PI using motion (https://github.com/Motion-Project/motion)
and this works like charm since years.

@velkrosmaak
I also use motion to detect and then stream the video via to the MM via MMM_SmartWebDisplay

In the motion config file (/etc/motion) search for

’ # Command to be executed when an event starts. (default: none)
'# An event starts at first motion detected after a period of no motion defined by event_gap
'# on_event_start value
'# Show iFrame in MagicMirror
on_event_start /etc/motion/notifyOn_MM.sh

'# Command to be executed when an event ends after a period of no motion
'# (default: none). The period of no motion is defined by option event_gap.
'# on_event_end value
'# Hide iFrame on MagicMirror
on_event_end /etc/motion/notifyOff_MM.sh

and the scripts could look like:

'# Show SmartWebDisplay in MagicMirror (iFrame no longer supported in MM 2.7.1)
curl --no-verbose http://:8080/remote?action=SHOW"&"module=module_10_MMM-SmartWebDisplay

Peter

@sdetweil
I finally got it working again!:thumbs_up:

I did a full fresh installation on a new SD card with complete latest Raspian and new MM and all the modules I used before…and still the same behavior: MMM-IFrame showed nothing and I got the same warnings as mentioned below.

Then I tried MMM-SmartWebDisplay by @AgP42 which finally displays my video stream again. (BTW: This also works with other URLs as described in the documentation)
Many thanks for this module.:clapping_hands:

For all having issues with MMM-iFrame, MMM-IFrame-Ping etc., try MMM-SmartWebDisplay.
Don’t forget to do a NPM install in the module folder once the module is cloned.

Thanks, Peter

@sdetweil Hi Sam, I tried that and the I got warnings about MMM-iFrame:

main.js:210 Resource interpreted as Document but transferred with MIME type multipart/x-mixed-replace: "http://192.168.178.8:8081/".
updateModuleContent	@	main.js:210
(anonymous)	@	main.js:139
updateDomWithContent	@	main.js:137
(anonymous)	@	main.js:119
Promise.then (async)		
(anonymous)	@	main.js:118
updateDom	@	main.js:109
updateDom	@	main.js:518
updateDom	@	module.js:358
(anonymous)	@	MMM-iFrame.js:25

The url is my other RasPi running Monitor displaying a video from my frontdoor.

As I stated in my 1st post, all was good since I upgraded to 2.7.1… :-(
Any more hints?
Thx, Peter

@BluP: Got additional information from the console:
update3
MMM-iFrame.js:26

Resource interpreted as Document but transferred with MIME type multipart/x-mixed-replace: “”.
main.js:210 Resource interpreted as Document but transferred with MIME type multipart/x-mixed-replace: “http://192.168.178.8:8081/”.

@alberttwong: can you give me a hint what needs to be adjusted?
@cowboysdude : I’ve searched the forum and also github and saw that yiou once had issues with iframe as well…any hints from your side?

Thx, Peter

Have you done a “npm install” for each module in the respective “…/modules/MMM-myModule” folder?
That was the issue when I updated from 2.4.0 to 2.7.1. no error messagage but blank/blck screen.

Hi everybody,

Just recently updated MM from 2.4.0 to 2.7.1 including all modules.
Unfortunately had issues with MMM-Remote-Control first but used the fixes described on Github.
But both MMM-iFrame or MMM-iFrame-Ping don’t show anything.
I used MMM-iFrame to show a live video stream from my frontdoor using another Pi with Motion and using a curl command to show the iFrame on the MM when movement was detected and hide it after a while. That worked perfectly. I also could use this via homekit and ask Siri to turn on the Frontdoor Cam for example.

I can see via http://MyMMIP:8080/remote?action=MODULE_DATA that the state of “hidden” changes between “true” and “false” when I use MMM-Remote-Control from my Mac or iPhone or when i use the buttons (show/hide Module iFrame)
But it shows nothing…

Anybody here who has an iFrame up and running with MM 2.7.1.

My other modules:
calendar_monthly
MMM-Carousel
MMM-iFrame-Ping or MMM-iFrame
MMM-RandomPhoto or MMM-BackgroundSlideshow
MMM-Tado
MMM-DWD-WarnWeather
MMM-ModuleScheduler
MMM-Remote-Control
MMM-Tools
MMM-EasyPix
MMM-MyCommute
MMM-Snow
MMM-Wunderlist
MMM-Buttons
MMM-NetworkScanner
MMM-syslog
netatmo

Thanks,

@BluP said in Do you use a PIR sensor? How do you hide it?:

@htilburgs

You May also think of some different solution: I‘m using a Hue Motion detector which is in my corridor anyway and controls the MM via MM-remotecontrol using the Http get requests through HomeKit and homebridge

@htilburgs

@axled
Thanks a lot!
Your syntax check did the trick. Now it works as expected!
Many thanks!:thumbs_up: