@sdetweil said in How Can I Mount my smart mirror to a wall?:

you could use C as well, using only the bottom screw… so it rotates…
this would allow the loop of cable at C to be in the open space behind the mirror, reducing the protusion from the wall to just the thickness of the mounting flange

Thank you so much! I’m just thinking if I don’t want to use a “hanger wire”, can i do it this way? And for the wall (hanging) side, I can go with something like “L screw hook hanger”, as the following in the second picture. What do you think?

@sdetweil said in How Can I Mount my smart mirror to a wall?:

@dentrax you are not screwing into the space with the slot, more the outside edge, in the 10mm NOT slotted

that is why I said its a shame, you don’t need so much slot… but too late now

u need the back panel to slide out without removing any fasteners… u said that in the beginning

but the slot is why you do not want to use C as the twisting could break the slot…

Thanks! I brought 2 Cs and 4 As yesterday. I’m sharing pictures to confirm if I fully understand what you’re proposing. :)

you do not want to use C as the twisting could break the slot

Making two screws to Cs will apply twisting force. I agree that. I guess a use-case like the first picture I drew is a bit risky, right?

Also, I’m thinking that is it more risky to attach a single screw both sides, since we only 10mm area, which is why we need to use strong screws, i guess. I just want to be sure that it’s reinforced enough as well.

I’m sorry that I keep pinging you about this thread. I hope this thread will help other people as well from whom come from search engines. (Or maybe it’s just a specific case for me, lol)

@sdetweil said in How Can I Mount my smart mirror to a wall?:

@dentrax u would mount it on the BACK surface, not the TOP
like this

red is the wire from the two hangers

to keep the unit appearing flush against the wall, you would need to add two bumpers at the bottom
same thickness of the a mount on the back…

the A hanger will rotate toward the wire centerpoint

Oh, I see now. Thanks for the illustration! That’s makes sense. But… I’m not sure if I can screw it into that narrow slider. It’s exactly 7mm. The sliding system will be broken, if the screw is long enough. 🤔 But at the same time, the hanger needs to be attached strongly. That’s my concern. :(

@sdetweil said in How Can I Mount my smart mirror to a wall?:

which will put a twisting force on the side of the frame as well as the weight force

Hmm, you are right. I think we don’t want to put twisting forces on the side corners.

I guess I need to find a hanger hook at (10mmx52mm) size and with just one screw so that it is able to rotate to point towards the center point?

So, something like this?

@sdetweil said in How Can I Mount my smart mirror to a wall?:

@dentrax how much space is left between the outside of the case and the back sliding panel?

it’s exactly 10 mm, vertically 52 mm. Would C is most suitable in this situation? What can I do alternatively?

Hello!

I finally almost completed my mirror. Behind the mirror, I did slightly different design. You can slide the wooden plate upside and downside. I did it on purpose, so I could maintain the internal in case of a situation.

I would like to hang it (in portrait style) on the wall. (Average weight: ~3 kg (6.61 lb)) But I really don’t know how to do it since I’m not good at craftsman things. I don’t want to block the slidable plate while implementing frame hanging hooks.

Do I need something like this? What would be your advice?

Thanks in advance…

(Not sure if this is appropriate category, feel free to move to correct one, thanks!)

You can find the project here: https://github.com/Dentrax/MMM-ArduPort

This module provides Arduino serial communication support with Raspberry PI.

I created this module for my project real-time ArduRMMMQ project.

This project is almost 2-3 years old. I did not even know that this forum existed back then. :)
I created it for my real-time operating system final project in the college at junior year. But we did not create a mirror physically, just demonstrated on the laptop. And, finally, here I am. I’ve finally built my own mirror. (physically) And just wanted to publish this module here. I’m looking forward to your feedback. ;)