How to turn off Raspberry Pi LEDs

sdetweil

@GuestMirror never heard of any option to turn off the LEDs except on pi0w.

sdetweil

@GuestMirror boot/config.txt is processed long before pm2 is started…

Fozi

@GuestMirror Try this in bootconfig.txt

# Turn off PWR LED
dtparam=pwr_led_trigger=none
dtparam=pwr_led_activelow=off
 
# Turn off ACT LED
dtparam=act_led_trigger=none
dtparam=act_led_activelow=off
 
# Turn off Ethernet ACT LED
dtparam=eth_led0=4
 
# Turn off Ethernet LNK LED
dtparam=eth_led1=4

GuestMirror

@sdetweil Is there a way to see if the boot/config.txt loads properly? I tried troubleshooting it by setting different things in there like rotating the display etc. however, even with all my other changes commented out nothing changes when booting.

GuestMirror

@Fozi I already tried that but it won’t work for some reason.

plainbroke

@Fozi @GuestMirror
Works on my RPi 4
I just copied and pasted to the bottom of the config.txt did a PM2 stop all and then sudo reboot and when it came backup they where on for a few seconds and then went off. @GuestMirror are you in the /boot/config.txt?

@Fozi said in How to turn off Raspberry Pi LEDs:

@GuestMirror Try this in bootconfig.txt

# Turn off PWR LED
dtparam=pwr_led_trigger=none
dtparam=pwr_led_activelow=off
 
# Turn off ACT LED
dtparam=act_led_trigger=none
dtparam=act_led_activelow=off
 
# Turn off Ethernet ACT LED
dtparam=eth_led0=4
 
# Turn off Ethernet LNK LED
dtparam=eth_led1=4

evroom

@GuestMirror

Hi,

I do not have a Pi 4 but on my Pi 3 Model B I have this:

sudo nano /boot/config.txt

# Disable the PWR LED
dtparam=pwr_led_trigger=none
dtparam=pwr_led_activelow=off

# Disable the Activity LED
dtparam=act_led_trigger=none
dtparam=act_led_activelow=off

crontab -e

@reboot echo 0 | sudo tee /sys/class/leds/led1/brightness

You can try this to see if the above cron entry works (before rebooting):

echo 0 | sudo tee /sys/class/leds/led1/brightness

Perhaps some stuff does not work or does the same, but both the power LED and activity LED on my Pi are off in the end.
Btw, on my Pi 3 Model B Plus, only the /root/config.txt line are needed.

Concerning the LAN LED’s I found following:

# Disable LAN-LEDs on Raspberry Pi 3B+
dtparam=eth_led0=14
dtparam=eth_led1=14

# Disable LAN-LEDs on Raspberry Pi 4
dtparam=eth_led0=4
dtparam=eth_led1=4

Good luck!

harney

here are the amendments to boot/config.txt file. For BULLSEYE, you have to use different parameters to make them work

these work for pi3 and pi 4

Pre BULLSEYE

Disable the PWR LED
dtparam=pwr_led_trigger=none
dtparam=pwr_led_activelow=off
Disable the Activity LED
dtparam=act_led_trigger=none
dtparam=act_led_activelow=off
Disable ethernet port LEDs
dtparam=eth_led0=4
dtparam=eth_led1=4

BULLSEYE ONLY

Disable the PWR LED
dtparam=pwr_led_trigger=default-on
dtparam=pwr_led_activelow=off
Disable the Activity LED
dtparam=act_led_trigger=none
dtparam=act_led_activelow=off
Disable Ethernet port LEDs
dtparam=eth_led0=4
dtparam=eth_led1=4