Modifying the Config File

BKeyport

@jimb that appears to be your windows computer, not the pi.

sdetweil

@jimb said in Modifying the Config File:

only mistake I made was making the MM auto-install.

u mean auto start??? install was my script

ssh doesn’t work unless you enable it on the pi

desktop, menu top left,
preferences
raspberry pi configuration
then the itnerfaces tab, click the slide on the ssh row,
then press ok…

if latest os, then you don’t have to boot

open a terminal window on pi
type

ip addr

you should see like this

pi@raspberrypi4:~ $ ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether dc:a6:32:20:b0:94 brd ff:ff:ff:ff:ff:ff
    inet 192.168.2.44/24 brd 192.168.2.255 scope global dynamic noprefixroute eth0
       valid_lft 50521sec preferred_lft 36219sec
    inet6 fe80::a5a6:f1d1:50e7:1c5/64 scope link 
       valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
    link/ether dc:a6:32:20:b0:95 brd ff:ff:ff:ff:ff:ff

in this setup my wifi (wlan0) is not connected but my ethernet (eth0) is

   inet 192.168.2.44

doesn’t matter what the PC says…

do you have a guest network at home and did u connect the pi to that?

can’t connect to it from home network if so… intentional firewall…

jimb

Sam, the Pi is connected via wireless. Yes, I meant autorun on my first post. I did change the Pi configuration to allow SSH. I have Eero mesh AP’s connected to my home network. I don’t know how to check if access is being blocked to the Pi. Since everything is fresh on the install it makes sense that the network is the culprit. The reason I went with a new install was to enable pasting config, etc. files here on the forum.

sdetweil

@jimb i understand… if you can use a terminal window on the pi, can you ping xxxx, where xxxx is the hostname or ip address of the windows pc?

what is the output of ip addr ?

i know it stinks, but you can post a pic, third icon from the right above the forum post editor

sdetweil

@jimb I’d also suggest trying my MMM-Config module, which presents a form for config.js including outside modules… all done with discovery of the installed modules and there parms…

some modules cause trouble… but there are ways around with some extra work… it may not be for you… another pile of work to learn, it it doesn’t work…

https://github.com/sdetweil/MMM-Config

it doesn’t help with module install, only configure

jimb

Sam,
OK progress on the network front. I spent some time yesterday on the phone with eero tech support. At rhe end they suggested connecting my PC wirelessly and seeing if I could ping the rasberry. It works. I can ping and SSH/Putty into the pi, but have an additional snag. It accepts the login and sends a password request. BUT, I can’t enter anything- the keyboard is dead at that point.

sdetweil

@jimb ok, sounds like the wifi network is a guest, not connected to the regular ethernet network…

don’t use putty

open a cmd.exe window

ssh user_name@machine_ip

add one of the tools

winscp or bitvise ssh clients

they will give you a filemanager view of the files and an ssh window ,
per system you connect to…

bitvise also provides a filemanager view of the pc filesystem , so you can drag/drop files in either direction… (you would only do that for logs to pc, of special bug fix file , to pi)

jimb

Sam, success! I have d/l’d the SSH gui program and here is my config.js file. I have deleted my apiKey

modules: [
		{
			module: "alert",
		},
		{
			module: "updatenotification",
			position: "top_bar"
		},
		{
			module: "clock",
			position: "top_left"
		},
		{
			module: "calendar",
			header: "US Holidays",
			position: "top_left",
			config: {
				calendars: [
					{
						fetchInterval: 7 * 24 * 60 * 60 * 1000,
						symbol: "calendar-check",
						url: "https://ics.calendarlabs.com/76/mm3137/US_Holidays.ics"
					}
				]
			}
		},
		{
			module: "compliments",
			position: "lower_third"
		},
		{
			module: "weather",
			position: "top_right",
			config: {
				weatherProvider: "openweathermap",
				apiVersion: "3.0",
				lat: 33.50872,
				lon: -96.612213,
				weatherEndpoint: "/onecall",
				type: "current",
				location: "Houston",
				locationID: "4699066", //ID from http://bulk.openweathermap.org/sample/city.list.json.gz; unzip the gz file and find your city
				apiKey: "8eca2aec"
			}
		},
		{
			module: "weather",
			position: "top_right",
			header: "Weather Forecast",
			config: {
				weatherProvider: "openweathermap",
				apiVersion: "3.0",
				lat: 33.50872,
				lon: -96.612213,
				weatherEndpoint: "/onecall",
				type: "forecast",
				location: "Houston",
				locationID: "4699066", //ID from http://bulk.openweathermap.org/sample/city.list.json.gz; unzip the gz file and find your city
				apiKey: "8
"
			}
		},
		{
			module: "newsfeed",
			position: "bottom_bar",
			config: {
				feeds: [
					{
						title: "New York Times",

sdetweil

@jimb missing some at the bottom

I assume the apikey with a new line inside is a removal edit problem

always wrap config.js content in code block

paste into editor
blank line above and below
select pasted text
hit button </>

jimb

Sam, here is a copy of the config.js (with the apiKey deleted)

let config = {
	address: "localhost",	// Address to listen on, can be:
							// - "localhost", "127.0.0.1", "::1" to listen on loopback interface
							// - another specific IPv4/6 to listen on a specific interface
							// - "0.0.0.0", "::" to listen on any interface
							// Default, when address config is left out or empty, is "localhost"
	port: 8080,
	basePath: "/",			// The URL path where MagicMirrorÂ² is hosted. If you are using a Reverse proxy
					  		// you must set the sub path here. basePath must end with a /
	ipWhitelist: ["127.0.0.1", "::ffff:127.0.0.1", "::1"],	// Set [] to allow all IP addresses
															// or add a specific IPv4 of 192.168.1.5 :
															// ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.1.5"],
															// or IPv4 range of 192.168.3.0 --> 192.168.3.15 use CIDR format :
															// ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.3.0/28"],

	useHttps: false, 		// Support HTTPS or not, default "false" will use HTTP
	httpsPrivateKey: "", 	// HTTPS private key path, only require when useHttps is true
	httpsCertificate: "", 	// HTTPS Certificate path, only require when useHttps is true

	language: "en",
	locale: "en-US",
	logLevel: ["INFO", "LOG", "WARN", "ERROR"], // Add "DEBUG" for even more logging
	timeFormat: 12,
	units: "imperial",

	modules: [
		{
			module: "alert",
		},
		{
			module: "updatenotification",
			position: "top_bar"
		},
		{
			module: "clock",
			timezone: "America/Chicago",
			showPeriodUpper: "true",
			showDate: "true",
			position: "top_left",
		},
	{
			module: "calendar",
			header: "US Holidays",
			position: "top_left",
			config: {
				calendars: [
					{
						fetchInterval: 7 * 24 * 60 * 60 * 1000,
						symbol: "calendar-check",
						url: "https://ics.calendarlabs.com/76/mm3137/US_Holidays.ics"
					}
				]
			}
		},
		{
			module: "compliments",
			position: "lower_third"
		},
		{			
			module: "weather",
			units: "imperial",
			windUnits: "imperial",
			tempUnits: "imperial",
			showPeriodUpper: "true",
			appendLocationNameToHeader: "true",
			colored: "true",
			position: "top_right",
			config: {
				apiVersion:"3.0",
				weatherProvider: "openweathermap",
				weatherEndpoint:"/onecall",
				lat: "33.50872",
				lon: "-96.612213",
				type: "current",
				location: "Houston",
				locationID: "4699066", //ID from http://bulk.openweathermap.org/sample/city.list.json.gz; unzip the gz file and find your city
				apiKey: "8acfbcab123ce212",
			}
		},
		{
			module: "weather",
			units: "imperial",
			winUnits: "imperial",
			tempUnits: "imperial",
			showPeriodUpper: "true",
			appendLocationNaneToHeader: "true",
			colored: "true",
			position: "top_right",
			header: "Weather Forecast",
			config: {
 				apiVersion:"3.0",
 				weatherProvider: "openweathermap",
				weatherEndpoint:"/onecall",
				lat: "33.50872",
 				lon:"-96.612213",	
 				type: "forecast",
     				location: "Houston",
				locationID: "4699066", //ID from http://bulk.openweathermap.org/sample/city.list.json.gz; unzip the gz file and find your city
					apiKey: "8eca2acaacfbcab123ce212",
			}
		},
		{
			module: "newsfeed",
			position: "bottom_bar",
			config: {
				feeds: [
					{
						title: "New York Times",
						url: "https://rss.nytimes.com/services/xml/rss/nyt/HomePage.xml"
					}
				],
				showSourceTitle: true,
				showPublishDate: true,
				broadcastNewsFeeds: true,
				broadcastNewsUpdates: true
			}
		},
	]
};

/*************** DO NOT EDIT THE LINE BELOW ***************/
if (typeof module !== "undefined") {module.exports = config;}