Read the statement by Michael Teeuw here.
EoF's Touch Screen Magic Mirror (Testing Phase)
-
@cyberphox Yeah this is a major snag for me. I’ve read up on some conductive ink pins that might do the trick repairing this. If it turns out that it doesn’t though… looks like I’ll be ordering a new panel :/
However, when the touch screen was working, it was working pretty good! Even better than on the demo video in my original post (which was on a windows machine).
There is some tricky calibration stuff you have to do to get it to play nice with the pi though.
-
You’re better off replacing the ribbon cable, if you can find a replacement. You’ll likely have to desolder it on the other end, then resolder the new one on.
Or, alternatively, take the ribbon cable off and solder your own wires and connector on.
-
@KirAsh4 Hi! I was actually able to get this working again (with some help). I tried a bunch of different things to avoid soldering because of the plastic on the ribbon, but I got to a point to where I said “whelp, it’s already broken so might as well just go for it” and believe it or not, it works now! I had to remove some of the plastic to expose the copper wire on both sides of the split, but then after that the solder completed the circuit and it’s working fine again.
I also went ahead and electric taped the hell out of the connector where the split was before so that this doesn’t happen again. Some heat shrink wrap was also applied for an extra layer of security :p
-
Basically the pulled a MacGyver then … :)
-
@KirAsh4 Haha basically. It works in my case though, as long as the connection stays secure, since this will be inside my enclosure anyways (once I get around to making one ;)).
-
So a bit of advice: when you have an enclosure (which I hope is sooner rather than later), affix the ribbon cable to something permanent. Even if you want to put hot snot on it (hot glue), just something to immobilize it so it can’t accidentally get snagged on something and get ripped, or that you accidentally pull on it …
-
@KirAsh4 Solid advice! I’m not sure how I would actually go about doing that for this particular cable though… let me show you what I’m working with here lol.
It’s a pretty short cable haha. Of course, it does have a USB controller and other cables that actually run to the pi. I will be sure to secure those as well though.
-
Hrm, yeah that’s short. Though honestly, I would wrap it behind the panel and tape it there. However, it also depends on where the rPi actually sits in relation to where this cable is.
-
@KirAsh4 Yeah that was kind of my idea to too.
-
A little progress on my mirror! Got the frame build, just need to paint now.
-
@EoF said in EoF's Touch Screen Magic Mirror (Testing Phase):
A little progress on my mirror! Got the frame build, just need to paint now.
If you can take a video when it’s all complete that’d be awesome. I’m trying to decide if I want to go the touch screen route with mirror film, or just use a mirror. I’m worried the mirror film might look silver and odd compared to a real glass mirror.
-
@geman220 Hi! Yes I will. I just finished painting it (2nd coat), so tomorrow I should be able to actually put it all together.
It will probably be in a new thread btw, since it will no longer be a testing phase at that point.
-
Great, do you have any input on the difference between the reflective film vs a real mirror? I have a feeling the reflective film is going to look more silver / grey almost metallic.
-
@EoF said in EoF’s Touch Screen Magic Mirror (Testing Phase):
hi there does your touch screen panel support multitouch or just single touch on linux?
also was it shipped with or without glass and did you mount this over the mirror or between the mirror and monitor?
Thanks!
-
@EoF Looks awesome!! I just ordered a 32" IR Frame for something I"m working on… can’t wait till it gets here :) Just a couple of screenshots ;)
-
@cowboysdude Oh that’s slick! :clap_tone1:
-
@Mykle1 Thank you!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login