MMM-DHT-Sensor

[STEFF92]

Hi,
I need some help. I tried to install the DHT module from bernardpletikosa (https://github.com/bernardpletikosa/MMM-DHT-Sensor). But when i start my MagicMirror i onley get a black screen.
Did i anything wrog in my config.js file? This is what i added:

{
			module: "MMM-DHT-Sensor",
			position: "bottom_right",
			config: {
				sensorTyp: "11",
				sensorPIN: "7",
				updateInterval: "2000 ms",
				animationSpeed: "0",
				titleText: "Raumtemperatur",
				units: "metric",
			}
		},

Thanks

[sdetweil]

U need another set of braces starting before “module”

And ending after the close brace of config

This new close brace, also needs a trailing comma

[STEFF92]

@sdetweil i tried it but then there was a black screen with the massage i should create a correct config.js file.

Befor i added the DHT-module, my MagicMirror was running. Here is my complete config.js file:

/* Magic Mirror Config Sample
 *
 * By Michael Teeuw http://michaelteeuw.nl
 * MIT Licensed.
 *
 * For more information how you can configurate this file
 * See https://github.com/MichMich/MagicMirror#configuration
 *
 */

var config = {
	address: "localhost", // Address to listen on, can be:
	                      // - "localhost", "127.0.0.1", "::1" to listen on loopback interface
	                      // - another specific IPv4/6 to listen on a specific interface
	                      // - "", "0.0.0.0", "::" to listen on any interface
	                      // Default, when address config is left out, is "localhost"
	port: 8080,
	ipWhitelist: ["127.0.0.1", "::ffff:127.0.0.1", "::1"], // Set [] to allow all IP addresses
	                                                       // or add a specific IPv4 of 192.168.1.5 :
	                                                       // ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.1.5"],
	                                                       // or IPv4 range of 192.168.3.0 --> 192.168.3.15 use CIDR format :
	                                                       // ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.3.0/28"],

	language: "en",
	timeFormat: 24,
	units: "metric",

	modules: [
		{
			module: "alert",
		},
		{
			module: "updatenotification",
			position: "top_bar"
		},
		{
			module: "clock",
			position: "top_left"
		},
		{
			module: "currentweather",
			position: "top_right",
			config: {
				location: "Castrop-Rauxel",
				locationID: "",  //ID from http://www.openweathermap.org/help/city_list.txt
				appid: "447e7403ed196c5dcfc895a3b85dd6b4"
			}
		},
		{
			module: "weatherforecast",
			position: "top_right",
			header: "Wettervorhersage",
			config: {
				location: "Castrop-Rauxel",
				locationID: "",  //ID from http://www.openweathermap.org/help/city_list.txt
				appid: "447e7403ed196c5dcfc895a3b85dd6b4"
			}
		},
		{
			module: "newsfeed",
			position: "bottom_bar",
			config: {
				feeds: [
					{
						title: "Tagesschau",
						url: "http://www.tagesschau.de/xml/rss2"
					},
					{
						title: "BILD News",
						url: "https://www.bild.de/rss-feeds/rss-16725492,feed=news.bild.html"
					},
					{
						title: "Kicker News",
						url: "http://rss.kicker.de/news/aktuell"
					},
					{
						title: "Kicker BVB",
						url: "http://rss.kicker.de/team/borussiadortmund"
					}
				],
				showSourceTitle: true,
				showPublishDate: true
			}
		},
		{
                      module: 'MMM-soccer',
                      position: 'bottom_left',
                      config: {
                              api_key: 'c7c930952f7a4d73951b33b2386d30c1',
                              colored: false,
                              show: 'GERMANY',
                              leagues: {"GERMANY":430},
                              }
                },
		{
			module: "MMM-DHT-Sensor",
			position: "bottom_right",
			config: {
				sensorTyp: "11",
				sensorPIN: "7",
				updateInterval: "2000 ms",
				animationSpeed: "0",
				titleText: "Raumtemperatur",
				units: "metric",
			}
		},
	]

};

/*************** DO NOT EDIT THE LINE BELOW ***************/
if (typeof module !== "undefined") {module.exports = config;}

[yawns]

Please try it this way:

{
	module: "MMM-DHT-Sensor",
	position: "bottom_right",
	config: {
		sensorTyp: 11,
		sensorPIN: 7,
		updateInterval: 2000,
		animationSpeed: 0,
		titleText: "Raumtemperatur",
		units: "metric",
	}
},

[STEFF92]

@yawns same problem, nothing else than a black screen

[binia]

Try please without the comma the last line.

		units: "metric"

[yawns]

@steff92 said in MMM-DHT-Sensor:

@yawns same problem, nothing else than a black screen

But you did run npm install in ~/MagicMirror/modules/MMM-DHT-Sensor ?

[STEFF92]

@binia doesn’t work

[STEFF92]

@yawns yes i did

[sdetweil]

cut and paste your entire config, and paste into jslint.com,
at the bottom of the screen check

node.js, long lines, single quotes, and whitespace mess

may have to comment out a few trailing commas…

should find the problem, if its config text related…

otherwise

start the mm from the commandline on the pi and see what the error reports,

[sdetweil]

jslint suggests removing the extra trailing commas

/* Magic Mirror Config Sample
 *
 * By Michael Teeuw http://michaelteeuw.nl
 * MIT Licensed.
 *
 * For more information how you can configurate this file
 * See https://github.com/MichMich/MagicMirror#configuration
 *
 */

var config = {
	address: "localhost", // Address to listen on, can be:
	                      // - "localhost", "127.0.0.1", "::1" to listen on loopback interface
	                      // - another specific IPv4/6 to listen on a specific interface
	                      // - "", "0.0.0.0", "::" to listen on any interface
	                      // Default, when address config is left out, is "localhost"
	port: 8080,
	ipWhitelist: ["127.0.0.1", "::ffff:127.0.0.1", "::1"], // Set [] to allow all IP addresses
	                                                       // or add a specific IPv4 of 192.168.1.5 :
	                                                       // ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.1.5"],
	                                                       // or IPv4 range of 192.168.3.0 --> 192.168.3.15 use CIDR format :
	                                                       // ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.3.0/28"],

	language: "en",
	timeFormat: 24,
	units: "metric",

	modules: [
		{
			module: "alert"
		},
		{
			module: "updatenotification",
			position: "top_bar"
		},
		{
			module: "clock",
			position: "top_left"
		},
		{
			module: "currentweather",
			position: "top_right",
			config: {
				location: "Castrop-Rauxel",
				locationID: "",  //ID from http://www.openweathermap.org/help/city_list.txt
				appid: "447e7403ed196c5dcfc895a3b85dd6b4"
			}
		},
		{
			module: "weatherforecast",
			position: "top_right",
			header: "Wettervorhersage",
			config: {
				location: "Castrop-Rauxel",
				locationID: "",  //ID from http://www.openweathermap.org/help/city_list.txt
				appid: "447e7403ed196c5dcfc895a3b85dd6b4"
			}
		},
		{
			module: "newsfeed",
			position: "bottom_bar",
			config: {
				feeds: [
					{
						title: "Tagesschau",
						url: "http://www.tagesschau.de/xml/rss2"
					},
					{
						title: "BILD News",
						url: "https://www.bild.de/rss-feeds/rss-16725492,feed=news.bild.html"
					},
					{
						title: "Kicker News",
						url: "http://rss.kicker.de/news/aktuell"
					},
					{
						title: "Kicker BVB",
						url: "http://rss.kicker.de/team/borussiadortmund"
					}
				],
				showSourceTitle: true,
				showPublishDate: true
			}
		},
		{
                      module: 'MMM-soccer',
                      position: 'bottom_left',
                      config: {
                              api_key: 'c7c930952f7a4d73951b33b2386d30c1',
                              colored: false,
                              show: 'GERMANY',
                              leagues: {"GERMANY":430}
                              }
                },
		{
			module: "MMM-DHT-Sensor",
			position: "bottom_right",
			config: {
				sensorTyp: "11",
				sensorPIN: "7",
				updateInterval: "2000 ms",
				animationSpeed: "0",
				titleText: "Raumtemperatur",
				units: "metric"
			}
		}
	]

};

/*************** DO NOT EDIT THE LINE BELOW ***************/
if (typeof module !== "undefined") {module.exports = config;}

[STEFF92]

@sdetweil i tried that code, but it doesnt work. Still the same problem.
I always start the MM in the command line with:

cd MagicMirror/
npm start

Then the black screen opens and i can’t see whats in the command line because if i want to stop MM i have to reboot the pi (I’m a total beginner, sorry, maybe there is an other possibility to stop without reboot).

I despair :loudly_crying_face:

[sdetweil]

@steff92 if u have a keyboard press ctrl-shift-i ( letter i) to open debug console.

Or start mirror in Dev mode, not full screen

npm start Dev

Alt-tab will also walk u between the available windows

[cyberdie]

This is my running config for this module:

		{
			module: "MMM-DHT-Sensor",
			position: "top_right",
			header: "Header",
			config: {
				sensorPin: 2,
				sensorType: 11,	
				updateInterval: 60 * 60 * 1000,
				initialLoadDelay: 0,
				animationSpeed: 1000,
				units: "metric",
				relativeScale: 35,
				debug: false
			}
		},