[Electron] display en screen after installing MMM-PIR-Sensor

RIKKO14

This post is deleted!

sdetweil

from the module folder do
npm install onoff --save

RIKKO14

I do npm install onoff --save in ~/MagicMirror/modules/MMM-PIR-Sensor and reboot
but the same problem :

0|mm       | [2020-08-21 13:36:17.541] [ERROR]  WARNING! Could not load config file. Starting with default configuration. Error found: Error: Cannot find module 'onoff'
0|mm       | Require stack:
0|mm       | - /home/pi/MagicMirror/modules/MMM-PIR-Sensor/node_helper.js
0|mm       | - /home/pi/MagicMirror/js/app.js
0|mm       | - /home/pi/MagicMirror/js/electron.js
0|mm       | - /home/pi/MagicMirror/node_modules/electron/dist/resources/default_app.asar/main.js

and

0|mm       | [2020-08-21 14:22:15.086] [ERROR]  WARNING! Could not load config file. Starting with default configuration. Error found: Error: The module '/home/pi/MagicMirror/modules/MMM-PIR-Sensor/node_modules/epoll/build/Release/epoll.node'
0|mm       | was compiled against a different Node.js version using
0|mm       | NODE_MODULE_VERSION 64. This version of Node.js requires
0|mm       | NODE_MODULE_VERSION 73. Please try re-compiling or re-installing
0|mm       | the module (for instance, using `npm rebuild` or `npm install`).

sdetweil

@RIKKO14 oh the joy, do

cd ~/MagicMirror/modules/MMM-PIR-Sensor
rm -rf node_modules
rm package-lock.json
npm install
npm install nan --save
npm install electron-rebuild --save
node node_modules/.bin/electron-rebuild

sdetweil

@RIKKO14 and u don’t need to reboot. just use the pm2 commands

pm2 restart 0

RIKKO14

I do this, MM reload but now after 2-3 secondes the screen turn off, GA with Jarvis works in background but i can’t find the screen of MM, if i do Ctrl + M
nothing is happening, there, I’m completely stuck…, I unplugged but the problem stay here…

sdetweil

@RIKKO14 is the screen actually powered off? did u enable ssh to get into a terminal window if desktop/mm has trouble?

if so I can issue commands there to turn on display tvservice or dpms…

I don’t use PIR, lots of troubles.

RIKKO14

I dont use ssh, only command on the py.
Instead of that, i think the py cut the power to the screen because the led of my screen is yellow like power off and not blue like something displayed.

RIKKO14

Yes, the screen actually powered off

RIKKO14

And I forgot to not the IP adress of my py, so I can’t use ssh now…
Pffff, I’m not lucky, every modules I want works instead of the PIR module…

RIKKO14

If i find my IP adress, Can you give me the commands to delete the problem ?

sdetweil

@RIKKO14 if u didn’t turn on ssh, it isn’t on, so can’t use it anyhow. look in your router to see what addresses were given out…

I do that quite often, then fix/reserve the address so I don’t have to remember

RIKKO14

ok, i find my IP adress (I’ve wrote it in excel file with some commandes i use) and I connected in SHH with putty,
thanks for your help to delete the commandh whose powered off my screen

RIKKO14

below my pm2 logs,
If that can help you…
https://www.cjoint.com/c/JHvqsqJ1QTT

RIKKO14

If it can help you this is my pm2 logs : https://www.cjoint.com/c/JHvqsqJ1QTT

sdetweil

@RIKKO14 looking at… hard to tell
do

pm2 stop 0
pm2 flush 
pm2 start 0

the will throw away the old logs…

RIKKO14

I do this, the problem still here…

sdetweil

@RIKKO14 it just makes the log easier to read. please post it again

RIKKO14

hre it is :
https://www.cjoint.com/c/JHvrPBCBgZT

RIKKO14

and this one (because i don’t if it it change something) : https://www.cjoint.com/c/JHvrUegIVzT after the command :

pm2 stop 0
pm2 flush 
pm2 start 0

and after only pm2 logs --lines=100

without pm2 status and pm2 stop 0