Modifying the Config File

sdetweil

@jimb if that is the only ip address, then it is not on your wifi or Ethernet networks.

127.0.0.1 is the fake internal only network

BKeyport

sounds to me like too much tinkering got the network FUBAR.

I’d reset and start over, personally.

jimb

Sam, from the Pi I can use the browser to get to the Internet so it has an IP address. I can ping Google from it, too. At this point I think the best thing would be for me to start over with a fresh installation. I don’t want to be a PITA here!

sdetweil

@jimb not a PITA. just odd that ip addr didn’t give u all adapters info

bhepler

@jimb said in Modifying the Config File:

IP Config from the OS prompt on the Pi yields -
“Link/loopback 'all zeros…”
“inet 127.0.0.0/8 scope host lo”

This should be the first entry of three in the response when you enter ip addr. The next entry should be your ethernet port, and the final entry should be your wireless LAN. My suggestion is to try this on your pi: ip addr | grep inet

Secondly, when Sam told you to switch on SSH, did you go into the config app and do it? You can get to it from the desktop but the fastest way is to type sudo raspi-config and then navigate to “Interface Options”->“SSH”. Make sure it is enabled.

jimb

Gents, my goal was not to build a watch, only to tell the time. I have bit the bullet and will be building a new image of the OS and setting it up to run from my PC. That way I’ll be able to copy configs for all to peruse, trying to get Magic Mirror up and running. Thanks for your continued support!

jimb

Sam, et all: I have installed a fresh copy of the OS to a new SD card , booted up the Pi, and installed a new copy of the MM2 files, etc. from Sam’s installation script. The only mistake I made was making the MM auto-install. I attempted SSH into the Pi to modify the config on my PC. Had the same “no connnection” issue I had before. However, I now have the IP address of the Pi and I’m not able to ping it from my PC. When the Pi boots this IP address is displayed in the upper right corner for a few seconds so I know it’s correct. An IP config /all display shows-

C:\Users\Owner>ipconfig /all

Windows IP Configuration

Host Name . . . . . . . . . . . . : DESKTOP-LE5LUCM
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : attlocal.net

Ethernet adapter Ethernet:

Connection-specific DNS Suffix . : attlocal.net
Description . . . . . . . . . . . : Realtek PCIe GbE Family Controller
Physical Address. . . . . . . . . : 78-E7-D1-C8-69-02
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : 2600:1700:d10:2900::681(Preferred)
Lease Obtained. . . . . . . . . . : Wednesday, November 29, 2023 1:44:08 AM
Lease Expires . . . . . . . . . . : Thursday, December 28, 2023 6:10:32 PM
IPv6 Address. . . . . . . . . . . : 2600:1700:d10:2900:17cb:6c66:31f8:87bb(Preferred)
Temporary IPv6 Address. . . . . . : 2600:1700:d10:2900:3974:7e8b:2c4:8999(Preferred)
Temporary IPv6 Address. . . . . . : 2600:1700:d10:2900:e81f:6b5c:4ac6:b88d(Deprecated)
Temporary IPv6 Address. . . . . . : 2600:1700:d10:2900:f895:4134:2f63:7933(Deprecated)
Link-local IPv6 Address . . . . . : fe80::3b70:ff2e:ecd1:4297%12(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.1.65(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Wednesday, November 29, 2023 1:44:03 AM
Lease Expires . . . . . . . . . . : Saturday, December 2, 2023 1:44:06 PM
Default Gateway . . . . . . . . . : fe80::3a3b:c8ff:fe33:13d9%12
192.168.1.254
DHCP Server . . . . . . . . . . . : 192.168.1.254
DHCPv6 IAID . . . . . . . . . . . : 158918609
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-25-B7-F6-59-78-E7-D1-C8-69-02
DNS Servers . . . . . . . . . . . : 2600:1700:d10:2900::1
192.168.1.254
2600:1700:d10:2900::1
NetBIOS over Tcpip. . . . . . . . : Enabled

Wireless LAN adapter Wi-Fi:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : 802.11n Wireless LAN Card
Physical Address. . . . . . . . . : 68-A3-C4-EA-95-83
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes

Wireless LAN adapter Local Area Connection* 1:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Wi-Fi Direct Virtual Adapter
Physical Address. . . . . . . . . : 68-A3-C4-EA-95-85
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes

Wireless LAN adapter Local Area Connection* 2:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Wi-Fi Direct Virtual Adapter #2
Physical Address. . . . . . . . . : 68-A3-C4-EA-95-86
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes

Wireless LAN adapter Local Area Connection* 11:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Hosted Network Virtual Adapter
Physical Address. . . . . . . . . : 68-A3-C4-EA-95-84
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes

C:\Users\Owner>

Does anyone see anything weird?

BKeyport

@jimb that appears to be your windows computer, not the pi.

sdetweil

@jimb said in Modifying the Config File:

only mistake I made was making the MM auto-install.

u mean auto start??? install was my script

ssh doesn’t work unless you enable it on the pi

desktop, menu top left,
preferences
raspberry pi configuration
then the itnerfaces tab, click the slide on the ssh row,
then press ok…

if latest os, then you don’t have to boot

open a terminal window on pi
type

ip addr

you should see like this

pi@raspberrypi4:~ $ ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether dc:a6:32:20:b0:94 brd ff:ff:ff:ff:ff:ff
    inet 192.168.2.44/24 brd 192.168.2.255 scope global dynamic noprefixroute eth0
       valid_lft 50521sec preferred_lft 36219sec
    inet6 fe80::a5a6:f1d1:50e7:1c5/64 scope link 
       valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
    link/ether dc:a6:32:20:b0:95 brd ff:ff:ff:ff:ff:ff

in this setup my wifi (wlan0) is not connected but my ethernet (eth0) is

   inet 192.168.2.44

doesn’t matter what the PC says…

do you have a guest network at home and did u connect the pi to that?

can’t connect to it from home network if so… intentional firewall…

jimb

Sam, the Pi is connected via wireless. Yes, I meant autorun on my first post. I did change the Pi configuration to allow SSH. I have Eero mesh AP’s connected to my home network. I don’t know how to check if access is being blocked to the Pi. Since everything is fresh on the install it makes sense that the network is the culprit. The reason I went with a new install was to enable pasting config, etc. files here on the forum.