Changing icons of the modules Current Weather and Weather Forecast

[Manu85]

@sdetweil
I use RealVNC Viewer and when I do ctrl-shift-i I have this window which opens I click at the top left and with my mouse I browse the lines, I have several lines with weather but when I click on them none opens another window

[sdetweil]

@Manu85 yes, good

click the arrow pointer in the red box
then move the mouse over the weather content in the left side page, it will select the content as it goes… make sure the entire weather content is selected
then click

[sdetweil]

@Manu85 when its auto selected it will look like this

[Manu85]

@sdetweil
it’s complicated, I can’t have a selection like you, I selected the icon at the top with the cloud and the moon I have lines that have changed on the table on the right but I don’t have another window that opens

[sdetweil]

@Manu85 i’ve never done this over vnc…

the right panel is just hidden on your vnc screen. you might be able to scroll right

if you are in the same house as MM, you dont need to use vnc to view the page

as long as your config.js says

address:"0.0.0.0",
ipWhiltelist:[],

then any machine on the same network can attach, so you can do this from your windows machine too… and do the debug from there as well

[Manu85]

@sdetweil my js config says that!

fig = {
	address: "localhost", // Address to listen on, can be:
	                      // - "localhost", "127.0.0.1", "::1" to listen on loopback interface
	                      // - another specific IPv4/6 to listen on a specific interface
	                      // - "", "0.0.0.0", "::" to listen on any interface
	                      // Default, when address config is left out, is "localhost"
	port: 8080,
	ipWhitelist: ["127.0.0.1", "::ffff:127.0.0.1", "::1"], // Set [] to allow all IP addresses
	                                                       // or add a specific IPv4 of 192.168.1.5 :
	                                                       // ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.1.5"],
	                                                       // or IPv4 range of 192.168.3.0 --> 192.168.3.15 use CIDR format :
	                                                       // ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.3.0/28"],

[sdetweil]

@Manu85 yes, that means only apps INSIDE the same machine can connect

change

address:"localhost",  // means only inside same machine

to

address:"0.0.0.0",  // alows any device on any network this machine is connected to to connect

then also the whitelist

comment out the current line

// ipWhitelist: [ 127.....

and add a new line

   ipWhitelist:[],  // don't filter any connecting client addresses

then restart mm…
if you know the ip address of the pi (and u had to use it for vnc)
then open a tab on you pc browser and do

http://MM_ip_address????:8080

[Manu85]

@sdetweil ok it’s done and it’s actually much better

[Manu85]

@sdetweil by doing ctrl shift i my window opened like this

[sdetweil]

@Manu85 yes, it just has the developers window docked on the bottom…

helps when trying to do layout… nothing changes

if you want it docked on the right, use the … menu top right of the dev window and change it…

[Manu85]

@sdetweil
when I position myself on a weather icon, it gives this, I cannot choose several I have a “grid” which follows the mouse and which changes when I move

[sdetweil]

@Manu85 yes, you have to drag the windows around/resize them in the developers window

[Manu85]

@sdetweil like that ?

[sdetweil]

@Manu85 yes, very good…

now, up two lines is the module entry in the content,
and you can see that the extra class name has been added
(in pink)

so, in custom.css

.current  xxx

will target (select) content in that element tree

if you move down to one of the spans of the content
in green, and expand that , you will see the icon line,
if you select that in the next pane to the right you will see where the info comes from

[Manu85]

@sdetweil
I do what you tell me, but I must admit that I’m lost :-) I actually saw the “current” in the lines so that means that the icon is in the custom css, it’s that right? if so why can’t I manage it? you are too strong

[sdetweil]

@Manu85 so close…

you have to click on the element with the icon name

here you have to expand the span element (gold box)
(the one you expanded below the gold box only has text in it, not an icon)

[Manu85]

@sdetweil
there, am I on it? I’m going to get there, I’m going to get there !!!

[sdetweil]

@Manu85 now in the second column of the dev windows you can see the icon info and where it came from, custom.css

[Manu85]

@sdetweil I try to move forward on the folder, I changed the destination folder for the “current” part by directing to a folder in css/icons/animated, but nothing changes, the supported icon is that of css/icons, red square (which keeps the properties, size, positioning of weather) I have the impression that “css/icons/animated” is not supported, green square, I think I am not far from the solution, but without your help I don’t think I’ll get there

[Manu85]

@sdetweil Thanks to you, I finally managed to configure the weather module with animated icons, I finally understood the advantages and the settings possible with the console (ctrl+shift+i) it also allowed me to make other settings on other modules, it’s been 5 years since I did this MM and I learned more with you in 3 days than in 5 years, a big thank you for your help