Started partial installation tonight…and I can say: what an absolutely beautiful and efficient installer! This is the best installer I have seen for a module.
I’m running it on a fresh installation of Raspberry Pi OS and fresh installation of MagicMirror with no other modules installed.
Ran into a small hiccup during the post-installation process, during audio configuration for the speakers. I can’t get any sound output.
It’s late so I will fiddle and experiment more tomorrow but in case anyone else runs into the same problem before I figure out a solution, I’ll leave some data below:
Sending audio output via aux cable from pi to monitor and can confirm audio is working when playing a youtube video.
Interestingly I hear a beep during this part of the installation, but nothing after that:
Do you want to check compatible GCC version [Y/n]
Your choice:
No sound from here onwards:
Checking Speaker and Microphone...
Do you want check your audio configuration [Y/n]
Your choice: Y
Checking audio output...
Make sure your speakers are on press [Yes].
Press [No] if you don't want to check. [Y/n]
Your choice: Y
Current configuration not working !
Did you hear Google beep? [Y/n]
Your choice: n
Selection of the speaker device
card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1]
card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones]
Indicate the card # to use [0-9]: 0
Indicate the device # to use [0-9]: 0
you have selected: hw:0,0 (plughw:0)
Checking audio output...
Make sure your speakers are on press [Yes].
Press [No] if you don't want to check. [Y/n]
Your choice: Y
Current configuration not working !
Did you hear Google beep? [Y/n]
Your choice: n
Selection of the speaker device
card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1]
card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones]
Indicate the card # to use [0-9]: 0
Indicate the device # to use [0-9]: 1
you have selected: hw:0,1 (plughw:0)
Checking audio output...
Make sure your speakers are on press [Yes].
Press [No] if you don't want to check. [Y/n]
Your choice: Y
Current configuration not working !
Did you hear Google beep? [Y/n]
Your choice: n
Selection of the speaker device
card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1]
card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones]
Indicate the card # to use [0-9]: 1
Indicate the device # to use [0-9]: 0
you have selected: hw:1,0 (plughw:1)
Checking audio output...
Make sure your speakers are on press [Yes].
Press [No] if you don't want to check. [Y/n]
Your choice: Y
Current configuration not working !
Did you hear Google beep? [Y/n]
Your choice: n
Selection of the speaker device
card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1]
card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones]
Indicate the card # to use [0-9]: 1
Indicate the device # to use [0-9]: 1
you have selected: hw:1,1 (plughw:1)
Checking audio output...
Make sure your speakers are on press [Yes].
Press [No] if you don't want to check. [Y/n]
Your choice: Y
Current configuration not working !
Did you hear Google beep? [Y/n]
Your choice: n
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1]
Subdevices: 4/4
Subdevice #0: subdevice #0
Subdevice #1: subdevice #1
Subdevice #2: subdevice #2
Subdevice #3: subdevice #3
card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones]
Subdevices: 4/4
Subdevice #0: subdevice #0
Subdevice #1: subdevice #1
Subdevice #2: subdevice #2
Subdevice #3: subdevice #3
EDIT:
I couldn’t sleep so I continued playing. I set audio speaker output to 1,0 which should be the correct configuration for me even though I couldn’t hear anything and I was getting an error. HOWEVER, in the next portion where I had to setup my microphone, I was able to hear my own voice playback.
Ran through the sample config example, and everything works perfectly with the brief testing I have done. Beautiful work Bugsounet!