mmm assistant mk2

[dvbit]

@Bugsounet great!
Will be testing.
And reporting quietly .

Tx again. Merci

Ps: good I have exactly the same setup.

[A Former User]

Attention … configuration is not the same.
Read Wiki

[dvbit]

@Bugsounet yep. Sure. Reading now. Installing tomorrow.and giving you feedback.
If you need help in giving simple support (i.e. dumb Linux, not reading the wiki … Aka not real issue / first level support I can try to help you there :-))

[A Former User]

no problem :)

[reddyman]

Started partial installation tonight…and I can say: what an absolutely beautiful and efficient installer! This is the best installer I have seen for a module.

I’m running it on a fresh installation of Raspberry Pi OS and fresh installation of MagicMirror with no other modules installed.

Ran into a small hiccup during the post-installation process, during audio configuration for the speakers. I can’t get any sound output.

It’s late so I will fiddle and experiment more tomorrow but in case anyone else runs into the same problem before I figure out a solution, I’ll leave some data below:

Sending audio output via aux cable from pi to monitor and can confirm audio is working when playing a youtube video.

Interestingly I hear a beep during this part of the installation, but nothing after that:

Do you want to check compatible GCC version [Y/n] 
Your choice: 

No sound from here onwards:

Checking Speaker and Microphone...
Do you want check your audio configuration [Y/n] 
Your choice: Y
Checking audio output...
Make sure your speakers are on press [Yes].
Press [No] if you don't want to check. [Y/n] 
Your choice: Y
Current configuration not working !
Did you hear Google beep? [Y/n] 
Your choice: n
Selection of the speaker device
card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1]
card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones]
Indicate the card # to use [0-9]: 0
Indicate the device # to use [0-9]: 0
you have selected: hw:0,0 (plughw:0)
Checking audio output...
Make sure your speakers are on press [Yes].
Press [No] if you don't want to check. [Y/n] 
Your choice: Y
Current configuration not working !
Did you hear Google beep? [Y/n] 
Your choice: n
Selection of the speaker device
card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1]
card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones]
Indicate the card # to use [0-9]: 0
Indicate the device # to use [0-9]: 1
you have selected: hw:0,1 (plughw:0)
Checking audio output...
Make sure your speakers are on press [Yes].
Press [No] if you don't want to check. [Y/n] 
Your choice: Y
Current configuration not working !
Did you hear Google beep? [Y/n] 
Your choice: n
Selection of the speaker device
card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1]
card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones]
Indicate the card # to use [0-9]: 1
Indicate the device # to use [0-9]: 0
you have selected: hw:1,0 (plughw:1)
Checking audio output...
Make sure your speakers are on press [Yes].
Press [No] if you don't want to check. [Y/n] 
Your choice: Y
Current configuration not working !
Did you hear Google beep? [Y/n] 
Your choice: n
Selection of the speaker device
card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1]
card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones]
Indicate the card # to use [0-9]: 1
Indicate the device # to use [0-9]: 1
you have selected: hw:1,1 (plughw:1)
Checking audio output...
Make sure your speakers are on press [Yes].
Press [No] if you don't want to check. [Y/n] 
Your choice: Y
Current configuration not working !
Did you hear Google beep? [Y/n] 
Your choice: n

aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1]
  Subdevices: 4/4
  Subdevice #0: subdevice #0
  Subdevice #1: subdevice #1
  Subdevice #2: subdevice #2
  Subdevice #3: subdevice #3
card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones]
  Subdevices: 4/4
  Subdevice #0: subdevice #0
  Subdevice #1: subdevice #1
  Subdevice #2: subdevice #2
  Subdevice #3: subdevice #3

---

EDIT:
I couldn’t sleep so I continued playing. I set audio speaker output to 1,0 which should be the correct configuration for me even though I couldn’t hear anything and I was getting an error. HOWEVER, in the next portion where I had to setup my microphone, I was able to hear my own voice playback.

Ran through the sample config example, and everything works perfectly with the brief testing I have done. Beautiful work Bugsounet!

[sdmydbr]

@Bugsounet thank you so much for this awesome module… works like a charm… 🤩

[djdocta]

@Bugsounet said in mmm assistant mk2:

AND… it’s now time !

Welcome to the new assistant : MMM-GoogleAssistant

Welcome to the new Assistant2Display: MMM-Assistant2Display

Will do some tests and debug on it but …
Impressive.
Good work.
Congrats. and THANKS for sharing.

[dvbit]

Installing . Flawless process

[dvbit]

and flawless install!
Thanks @Bugsounet

[dvbit]

A2D was not working at first launch.
npm rebuild in the directory did the trick.
Working now