Read the statement by Michael Teeuw here.
mmm assistant mk2
-
@dvbit: thx :)
Time -> 23:30
Deploy new Assistant in 30 min ! -
Bien heureux de t’aider si tu veux. Je suis italien mais je parle francais. Meme si c’est seulement pour traduire ;-)
-
AND… it’s now time !
Welcome to the new assistant : MMM-GoogleAssistant
Welcome to the new Assistant2Display: MMM-Assistant2Display
-
@Bugsounet great!
Will be testing.
And reporting quietly .Tx again. Merci
Ps: good I have exactly the same setup.
-
Attention … configuration is not the same.
Read Wiki -
@Bugsounet yep. Sure. Reading now. Installing tomorrow.and giving you feedback.
If you need help in giving simple support (i.e. dumb Linux, not reading the wiki … Aka not real issue / first level support I can try to help you there :-)) -
no problem :)
-
Started partial installation tonight…and I can say: what an absolutely beautiful and efficient installer! This is the best installer I have seen for a module.
I’m running it on a fresh installation of Raspberry Pi OS and fresh installation of MagicMirror with no other modules installed.
Ran into a small hiccup during the post-installation process, during audio configuration for the speakers. I can’t get any sound output.
It’s late so I will fiddle and experiment more tomorrow but in case anyone else runs into the same problem before I figure out a solution, I’ll leave some data below:
Sending audio output via aux cable from pi to monitor and can confirm audio is working when playing a youtube video.
Interestingly I hear a beep during this part of the installation, but nothing after that:
Do you want to check compatible GCC version [Y/n] Your choice:No sound from here onwards:
Checking Speaker and Microphone... Do you want check your audio configuration [Y/n] Your choice: Y Checking audio output... Make sure your speakers are on press [Yes]. Press [No] if you don't want to check. [Y/n] Your choice: Y Current configuration not working ! Did you hear Google beep? [Y/n] Your choice: n Selection of the speaker device card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1] card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones] Indicate the card # to use [0-9]: 0 Indicate the device # to use [0-9]: 0 you have selected: hw:0,0 (plughw:0) Checking audio output... Make sure your speakers are on press [Yes]. Press [No] if you don't want to check. [Y/n] Your choice: Y Current configuration not working ! Did you hear Google beep? [Y/n] Your choice: n Selection of the speaker device card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1] card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones] Indicate the card # to use [0-9]: 0 Indicate the device # to use [0-9]: 1 you have selected: hw:0,1 (plughw:0) Checking audio output... Make sure your speakers are on press [Yes]. Press [No] if you don't want to check. [Y/n] Your choice: Y Current configuration not working ! Did you hear Google beep? [Y/n] Your choice: n Selection of the speaker device card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1] card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones] Indicate the card # to use [0-9]: 1 Indicate the device # to use [0-9]: 0 you have selected: hw:1,0 (plughw:1) Checking audio output... Make sure your speakers are on press [Yes]. Press [No] if you don't want to check. [Y/n] Your choice: Y Current configuration not working ! Did you hear Google beep? [Y/n] Your choice: n Selection of the speaker device card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1] card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones] Indicate the card # to use [0-9]: 1 Indicate the device # to use [0-9]: 1 you have selected: hw:1,1 (plughw:1) Checking audio output... Make sure your speakers are on press [Yes]. Press [No] if you don't want to check. [Y/n] Your choice: Y Current configuration not working ! Did you hear Google beep? [Y/n] Your choice: naplay -l **** List of PLAYBACK Hardware Devices **** card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1] Subdevices: 4/4 Subdevice #0: subdevice #0 Subdevice #1: subdevice #1 Subdevice #2: subdevice #2 Subdevice #3: subdevice #3 card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones] Subdevices: 4/4 Subdevice #0: subdevice #0 Subdevice #1: subdevice #1 Subdevice #2: subdevice #2 Subdevice #3: subdevice #3
EDIT:
I couldn’t sleep so I continued playing. I set audio speaker output to 1,0 which should be the correct configuration for me even though I couldn’t hear anything and I was getting an error. HOWEVER, in the next portion where I had to setup my microphone, I was able to hear my own voice playback.Ran through the sample config example, and everything works perfectly with the brief testing I have done. Beautiful work Bugsounet!
-
@Bugsounet thank you so much for this awesome module… works like a charm… 🤩
-
@Bugsounet said in mmm assistant mk2:
AND… it’s now time !
Welcome to the new assistant : MMM-GoogleAssistant
Welcome to the new Assistant2Display: MMM-Assistant2Display
Will do some tests and debug on it but …
Impressive.
Good work.
Congrats. and THANKS for sharing.
