Magic Mirror with touchscreen Display/Monitor

core

Hi,

thank you very much for your replies.

An IR touch overlay is unfortunately not possible in my case. The mirror is frameless and clamped in 4 holders (2 above and 2 at the bottom). That’s why i am looking for a touch display which can be mounted under the glass.

Best regards

sdetweil

@core said in Magic Mirror with touchscreen Display/Monitor:

That’s why i am looking for a touch display which can be mounted under the glass.

that doesn’t exist. the monitor is dependent on human skin resistance (try it with a glove on)
the mirror glass would block that

core

@sdetweil
Ok, but a PCAP Touchfoil under the glass, mounted between a LED display and the Mirroview, will work for sure (asked Pilkington and the company selling the foil).

Best regards

sdetweil

@core but this is effectively the same as the ir frame… the special touchfoil does the work… NOT the monitor…

cowboysdude

I have a 24" one that after I bought it found out that it will not work in Linux so my only option is to install MM on Windows … ugh. So when I can come across a NUC or something small I will until then …

BJK

@Snille Hi Snille
I have had greate use of xin.sh file to run at start. It contained the:
“DISPLAY=:0.0 xinput --set-prop “Multi touch Multi touch overlay device” “Coordinate Transformation Matrix” 0 1 0 -1 0 1 0 0 1”
However, now using the pm2 start xin.sh for automatic start, I get an error in the pm2 log
What do you use to correct the ir-frame ?
Best
Bo

sdetweil

@BJK what is the error?

BJK

@sdetweil

Well, I start the xin.sh with PM2 and it works with calibrating the IR-frame:

xin.sh:
#!/bin/bash
DISPLAY=:0.0 xinput --set-prop “Multi touch Multi touch overlay device” “Coordinate Transformation Matrix” 0 -1 1 1 0 0 0 0 1

However, after the mm.sh (the MagicMirror) has started, then when I go back to Raspberry disktop the the Calibration is off again. If I then run the xin.sh with “pm2 start xin.sh” in a terminal window then the calibration is okay again.

This is the error that I get from pm2 log file:

Bo@MMpi:~ $ pm2 list
┌────┬────────────────────┬──────────┬──────┬───────────┬──────────┬──────────┐
│ id │ name │ mode │ ↺ │ status │ cpu │ memory │
├────┼────────────────────┼──────────┼──────┼───────────┼──────────┼──────────┤
│ 0 │ xin │ fork │ 15 │ errored │ 0% │ 0b │
└────┴────────────────────┴──────────┴──────┴───────────┴──────────┴──────────┘
[PM2][WARN] Current process list is not synchronized with saved list. App led mm differs. Type ‘pm2 save’ to synchronize.
Bo@MMpi:~ $ pm2 log
[TAILING] Tailing last 15 lines for [all] processes (change the value with --lines option)
/home/Bo/.pm2/pm2.log last 15 lines:
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] online
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] exited with code [0] via signal [SIGINT]
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] starting in -fork mode-
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] online
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] exited with code [0] via signal [SIGINT]
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] starting in -fork mode-
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] online
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] exited with code [0] via signal [SIGINT]
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] starting in -fork mode-
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] online
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] exited with code [0] via signal [SIGINT]
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] starting in -fork mode-
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] online
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] exited with code [0] via signal [SIGINT]
PM2 | 2022-03-31T20:11:38: PM2 log: Script /home/Bo/xin.sh had too many unstable restarts (16). Stopped. “errored”

/home/Bo/.pm2/logs/xin-out.log last 15 lines:
/home/Bo/.pm2/logs/xin-error.log last 15 lines:
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Unable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyInvalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Unable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyInvalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Unable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server

Should I do something else with pm2 or run the xin.sh in an other way?

It would be so nice to have i done automatically :beaming_face_with_smiling_eyes:

Best Bo

BJK

@sdetweil

Well, I start the xin.sh with PM2 and it works with calibrating the IR-frame:

xin.sh:
#!/bin/bash
DISPLAY=:0.0 xinput --set-prop “Multi touch Multi touch overlay device” “Coordinate Transformation Matrix” 0 -1 1 1 0 0 0 0 1

However, after the mm.sh (the MagicMirror) has started, then when I go back to Raspberry disktop the the Calibration is off again. If I then run the xin.sh with “pm2 start xin.sh” in a terminal window then the calibration is okay again.

This is the error that I get from pm2 log file:

Bo@MMpi:~ $ pm2 list
┌────┬────────────────────┬──────────┬──────┬───────────┬──────────┬──────────┐
│ id │ name │ mode │ ↺ │ status │ cpu │ memory │
├────┼────────────────────┼──────────┼──────┼───────────┼──────────┼──────────┤
│ 0 │ xin │ fork │ 15 │ errored │ 0% │ 0b │
└────┴────────────────────┴──────────┴──────┴───────────┴──────────┴──────────┘
[PM2][WARN] Current process list is not synchronized with saved list. App led mm differs. Type ‘pm2 save’ to synchronize.
Bo@MMpi:~ $ pm2 log
[TAILING] Tailing last 15 lines for [all] processes (change the value with --lines option)
/home/Bo/.pm2/pm2.log last 15 lines:
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] online
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] exited with code [0] via signal [SIGINT]
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] starting in -fork mode-
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] online
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] exited with code [0] via signal [SIGINT]
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] starting in -fork mode-
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] online
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] exited with code [0] via signal [SIGINT]
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] starting in -fork mode-
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] online
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] exited with code [0] via signal [SIGINT]
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] starting in -fork mode-
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] online
PM2 | 2022-03-31T20:11:38: PM2 log: App [xin:0] exited with code [0] via signal [SIGINT]
PM2 | 2022-03-31T20:11:38: PM2 log: Script /home/Bo/xin.sh had too many unstable restarts (16). Stopped. “errored”

/home/Bo/.pm2/logs/xin-out.log last 15 lines:
/home/Bo/.pm2/logs/xin-error.log last 15 lines:
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Unable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyInvalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Unable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyInvalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Unable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server
0|xin | Invalid MIT-MAGIC-COOKIE-1 keyUnable to connect to X server

Should I do something else with pm2 or run the xin.sh in an other way?

It would be so nice to have i done automatically 😁

the mm.sh file:
cd ~/MagicMirror
DISPLAY=:0 npm start

Best Bo

sdetweil

@BJK first

do
pm2 save

to sync the disk list with the memory list of things pm2 manages

then do

pm2 info 0

to get the startup info from the task definition

we’re you running as root ( or using sudo ) when u did the pm2 start xin.sh?