NPM run start cannot be used

[史新瑞]

@sdetweil
Then it’s full screen darkness

[史新瑞]

@kayakbabe > magicmirror@2.20.0 start

DISPLAY=“${DISPLAY:=:0}” ./node_modules/.bin/electron js/electron.js

/home/pi/MagicMirror/node_modules/electron/index.js:17
throw new Error(‘Electron failed to install correctly, please delete node_modules/electron and try installing again’);
^

Error: Electron failed to install correctly, please delete node_modules/electron and try installing again
at getElectronPath (/home/pi/MagicMirror/node_modules/electron/index.js:17:11)
at Object. (/home/pi/MagicMirror/node_modules/electron/index.js:21:18)
at Module._compile (node:internal/modules/cjs/loader:1105:14)
at Object.Module._extensions…js (node:internal/modules/cjs/loader:1159:10)
at Module.load (node:internal/modules/cjs/loader:981:32)
at Function.Module._load (node:internal/modules/cjs/loader:822:12)
at Module.require (node:internal/modules/cjs/loader:1005:19)
at require (node:internal/modules/cjs/helpers:102:18)
at Object. (/home/pi/MagicMirror/node_modules/electron/cli.js:3:18)
at Module._compile (node:internal/modules/cjs/loader:1105:14)

[sdetweil]

@史新瑞

 cd ~/MagicMirror
npm install electron@19.0.6

for the other black screen

see https://forum.magicmirror.builders/topic/15778/fix-for-black-screen-in-2-16-and-later/

[史新瑞]

@sdetweil Thank you. NPM can now be used to run and start, but the weather module cannot be displayed, as shown below

[史新瑞]

@史新瑞 This is the same config.js file under two different operating modes

[sdetweil]

@史新瑞 show any messages

[史新瑞]

@sdetweil There is no error message

[sdetweil]

@史新瑞 the messages where mm is started

npm start or
pm2 logs

[史新瑞]

@sdetweil What is described here is my latest problem. Sorry, I didn’t make it clear

[sdetweil]

@史新瑞 is it current or forecast mode? which provider?

[sdetweil]

@史新瑞 I just added my openweather api key to the starting config.js

		{
			module: "weather",
			position: "top_right",
			config: {
				weatherProvider: "openweathermap",
				type: "current",
				location: "New York",
				locationID: "5128581", //ID from http://bulk.openweathermap.org/sample/city.list.json.gz; unzip the gz file and find your city
				apiKey: "a6bf9feaa86bc2677df1e5fsdasdasd46bd79d"
			}
		},
		{
			module: "weather",
			position: "top_right",
			header: "Weather Forecast",
			config: {
				weatherProvider: "openweathermap",
				type: "forecast",
				location: "New York",
				locationID: "5128581", //ID from http://bulk.openweathermap.org/sample/city.list.json.gz; unzip the gz file and find your city
				apiKey: "a6bf9feaa86bc2677df1e5f46bd79dsdasd"
			}
		},

and both worked (the apikeys are mangled here so won’t work anywhere else)

[史新瑞]

@sdetweil I don’t use the same API as you, and your last reply revealed your key which is not good

[sdetweil]

@史新瑞 my key was mangled, so not useable… just wanted it to be clear for you…
default provider is openweather

I asked you what provider and type… (current or forecast)

I can get api keys to test too

[史新瑞]

@sdetweil If possible, I would like to try your API tomorrow, but this is only a test, and this is based on your consent. Generally, I will not use your API, I will continue to use my own API, I hope you can agree

[sdetweil]

@史新瑞 I don’t understand ‘API’

API is the method of getting data… we don’t expose that outside the module.
of course u could change the code if u know javascript.

you could certainly use the openeweather source…

[史新瑞]

@sdetweil To tell the truth, I didn’t remember it. Please allow me to check it tomorrow morning and tell you

[sdetweil]

@史新瑞 ok… I am US central time… Sunday Aug 14, 11:30 am .

[史新瑞]

@sdetweil I mean only the weather API, that is, the key of your openweather. I will come back to you for advice in nine hours, that is, around 8:00 p.m. us time. I hope you have time, and I hope you don’t hate me. Thank you again. I wish you good health and good luck. I’ll be with you all the time

[sdetweil]

@史新瑞 no opinion of you. just working on problems. many new users come and we work thru things…

see u later

[史新瑞]

@sdetweil
Good evening. I just woke up

/* MagicMirror² Config Sample
*
* By Michael Teeuw https://michaelteeuw.nl
* MIT Licensed.
*
* For more information on how you can configure this file
* see https://docs.magicmirror.builders/configuration/introduction.html
* and https://docs.magicmirror.builders/modules/configuration.html
*/
   
let config = {
   address: "localhost", 	// Address to listen on, can be:
   						// - "localhost", "127.0.0.1", "::1" to listen on loopback interface
   						// - another specific IPv4/6 to listen on a specific interface
   						// - "0.0.0.0", "::" to listen on any interface
   						// Default, when address config is left out or empty, is "localhost"
   port: 8080,
   basePath: "/", 	// The URL path where MagicMirror² is hosted. If you are using a Reverse proxy
   				// you must set the sub path here. basePath must end with a /
   ipWhitelist: ["127.0.0.1", "::ffff:127.0.0.1", "::1"], 	// Set [] to allow all IP addresses
   														// or add a specific IPv4 of 192.168.1.5 :
   														// ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.1.5"],
   														// or IPv4 range of 192.168.3.0 --> 192.168.3.15 use CIDR format :
   														// ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.3.0/28"],

   useHttps: false, 		// Support HTTPS or not, default "false" will use HTTP
   httpsPrivateKey: "", 	// HTTPS private key path, only require when useHttps is true
   httpsCertificate: "", 	// HTTPS Certificate path, only require when useHttps is true

   language: "zh-cn",
   locale: "zh",
   logLevel: ["INFO", "LOG", "WARN", "ERROR"], // Add "DEBUG" for even more logging
   timeFormat: 24,
   units: "metric",
   // serverOnly:  true/false/"local" ,
   // local for armv6l processors, default
   //   starts serveronly and then starts chrome browser
   // false, default for all NON-armv6l devices
   // true, force serveronly mode, because you want to.. no UI on this device

   modules: [
   	{
   		module: "alert",
   	},
   	{
   		module: "updatenotification",
   		position: "top_bar"
   	},
   	{
   		module: "clock",
   		position: "top_left"
   	},
   	{
   		module: "calendar",
   		header: "US Holidays",
   		position: "top_left",
   		config: {
   			calendars: [
   				{
   					symbol: "calendar-check",
   					url: "webcal://www.calendarlabs.com/ical-calendar/ics/76/US_Holidays.ics"
   				}
   			]
   		}
   	},
   //	{
   //		module: "compliments",
   //		position: "lower_third"
   //	},
   		{
   	module: "weather",
   	position: "top_right",
   	config: {
   		weatherProvider:"weatherbit",
   		weatherEndpoint:"/current/forecast/daily",
   		apiKey:"aa03f670e4944ac3a086f92482a5e25e",
   		// See 'Configuration options' for more information.
   		lat:"40.5",
   		lon:"116.5",
   		showSun:"true",
   		colored:"true",
   		maxNumberOfDays:"5"
   	}
   },
   	
   
   	/*  显示图片
   	 **/ {
   			module: "MMM-ImagesPhotos",
   			position: "middle_center",
   			config: {
   				opacity: 0.5,
   				animationSpeed: 1000,
   				updateInterval: 5000,
   				maxWidth:"500px",
   				maxHeight:"200px",
   				backgroundColor: 'grey',  // not used if fill is true
   				fill: false,   // fill around image with blurred copy of image
   				blur: 10,   // only used if fill is true
   			}
   		},
   		{
   	module: "helloworld",
   	position: "bottom_bar",	// This can be any of the regions.
   	config: {
   		// See 'Configuration options' for more information.
   		
   		text: "Hi! May I help you?"
   		
   	}
   },
   

   	
   {
	module: 'MMM-SimpleText',
	position: 'bottom_right',
	config: {
   		fontURL: {
   		  'value': 'Tahoma, Geneva, sans-serif'
   		},
   		fontSize: {
   		  'value': 'small'
   		},
   		fontStyle: {
   		  'value': 'italic'
   		},
   		color: {
   		  'value': '#FFFFFF'
   		},
   		refreshMs: {
   		  'value': '10000'
   		},
   		filePath: {
   		  'value': '123.txt'
   		},
   	}
},
   
   

   ]
};

/*************** DO NOT EDIT THE LINE BELOW ***************/
if (typeof module !== "undefined") {module.exports = config;}