Made a birthday module

plainbroke

@cgillinger
I installed your module, it does nothing when its turn comes up in MMM-pages.
I am running Bookworm, MM 2.30 on a Pi 4 8gb. How do I pick the messages?
Not quite enough information to run this module.
Please help with the setup…

cgillinger

@plainbroke Im running Linux Mint and this is my config from config.js:

 {
   module: "MMM-Birthday",
      position: "middle_center", 
      config: {
          birthdays: [
              { name: "Eric", date: "01-26" },
              { name: "Lisa", date: "07-01" },
              { name: "Sigrid", date: "07-15" },
              { name: "Lars", date: "07-17" },
              { name: "Firas", date: "11-26" }
          ],
          fireworkDuration: "infinite",
          confettiDuration: "infinite"
      }
    },

This works for me. Mind sharing your config.js, to see if something is up there? Have you run npm install?

And you dont pick messages, the module picks for you (or you can just edit the correct language json and enter the same message. This is for instance the en.json for english:

{
“MESSAGES”: [
“🎉 Happy Birthday, {name}! 🎂”,
“🎈 Best wishes on your special day, {name}! 🎁”,
“🌟 Have a fantastic birthday, {name}! 🎊”,
“✨ Wishing you a wonderful birthday, {name}! 🎈”,
“🎊 May your day be filled with joy, {name}! 🌟”
]
}

And to be clear: The module only activates on birthdays. Otherwise it just sits invisble.

plainbroke

@cgillinger
Yes did the npm install
Here is the section out of my config.js

                {
                        module: "MMM-Birthday",
                        position: "middle_center", // Module will be centered during celebrations
                        config: {
                                birthdays: [
                                        { name: "Test1", date: "1-21" },
                                        { name: "Test2", date: "1-22" },
                                        { name: "Test3", date: "1-23" },
                                        { name: "Test4", date: "1-24" },
                                        { name: "Test5", date: "1-25" }
                                ],
                                fireworkDuration: "infinite", // or specific duration in milliseconds
                                confettiDuration: "infinite"  // or specific duration in milliseconds
                        }
                },

cgillinger

@plainbroke Question: Have you tried running it without MMM-Pages? Im not familiar with the functionality of that module (but I’ll look into it)

cgillinger

After looking at MMM-pages I think the issue is that MMM-Birthday uses special positioning to ensure its celebrations are always visible (it needs to be on top of everything else to work properly). However, this means it doesn’t play nicely with MMM-Pages’ normal way of showing and hiding modules.

First suggestion: Add MMM-Birthday to MMM-Pages’ fixed modules:

config: {
fixed: [“MMM-page-indicator”, “MMM-Birthday”]
}

This should tell MMM-Pages to leave MMM-Birthday alone and let it handle its own visibility, which should resolve the issue while maintaining all the celebration effects.

sdetweil

@cgillinger the other thing you can do is add support for the

suspend(){}
and resume{}

methods in your modulename.js

suspend means being hidden

resume means being shown

plainbroke

@cgillinger
Well I tried your idea about putting MMM-Birthday in the “fixed” area in Pages.
I guess I can try your idea of using it without MMM-Pages, but it would be better if you could fix your module per sdetweil’s suggestion.

plainbroke

@cgillinger
I tried your idea, I renamed my config.js to config.js2
copied the config.js.sample to config.js
added this to the new config.js

/* Config Sample
 *
 * For more information on how you can configure this file
 * see https://docs.magicmirror.builders/configuration/introduction.html
 * and https://docs.magicmirror.builders/modules/configuration.html
 *
 * You can use environment variables using a `config.js.template` file instead of `config.js`
 * which will be converted to `config.js` while starting. For more information
 * see https://docs.magicmirror.builders/configuration/introduction.html#enviromnent-variables
 */
let config = {
        address: "192.168.1.222",       // Address to listen on, can be:
                                                        // - "localhost", "127.0.0.1", "::1" to listen on loopback interface
                                                        // - another specific IPv4/6 to listen on a specific interface
                                                        // - "0.0.0.0", "::" to listen on any interface
                                                        // Default, when address config is left out or empty, is "localhost"
        port: 8080,
        basePath: "/",  // The URL path where MagicMirror² is hosted. If you are using a Reverse proxy
        ipWhitelist: [],        // Set [] to allow all IP addresses

        useHttps: false,                        // Support HTTPS or not, default "false" will use HTTP
        httpsPrivateKey: "",    // HTTPS private key path, only require when useHttps is true
        httpsCertificate: "",   // HTTPS Certificate path, only require when useHttps is true

        language: "en",
        locale: "en-US",   // this variable is provided as a consistent location

        logLevel: ["INFO", "LOG", "WARN", "ERROR"], // Add "DEBUG" for even more logging
        timeFormat: 12,
        units: "imperical",

        modules: [
                {
                        module: "MMM-Birthday",
                        position: "middle_center", // Module will be centered d>
                        config: {
                                birthdays: [
                                        { name: "Test1", date: "1-21" },
                                        { name: "Test2", date: "1-22" },
                                        { name: "Test3", date: "1-23" },
                                        { name: "Test4", date: "1-24" },
                                        { name: "Test5", date: "1-25" }
                                ],
                                fireworkDuration: "infinite", // or specific du>
                                confettiDuration: "infinite"  // or specific du>
                        }
                },
        ],
};

/*************** DO NOT EDIT THE LINE BELOW ***************/
if (typeof module !== "undefined") { module.exports = config; }

Still does not work.
I removed and reinstalled
Still nothing. Maybe it only works on MINT?

sdetweil

@plainbroke you can also use the environment variable to set the config file

export MM_CONFIG_FILE=config/xxxxx.js
npm start
or
npm run server

Both will use that config

export MM_CONFIG_FILE=

To reset it

plainbroke

@sdetweil
I got it to work on another pi4 with only 4 mb ram.
On the exact same setup
Bookworm
MM 2.30
fully updated.
It seems it has to be the only module besides some of the default ones.
Which it covers up completely like the MPlayer does…
Good thing I have an extra pi, I guess. The wifey likes it alot…
I thought it would be cool add-on for my main mirror that is in the living room right above the TV. Gives us something to focus on during commercial’s…
Updated your MMM-Config. LOOKING better every update…