Read the statement by Michael Teeuw here.
Powering my mirror?
-
You split the 12V output of your power supply. One set of wires (plus and Gnd) goes to your LCD controller board (check polarity!) and one set to your step-down-converter, which is regulated to 5.1V for the Pi.
-
My point is that all the power supply’s under 80W only have one set of output wires.
-
Just use luster terminals.
-
@MadScientist sorry for so many questions. But won’t I need to solder them in a “T”? Or get a T splice?
-
Don’t be afraid to ask…
Pic says more than a thousand words…
You can solder the wires together but that’s not really needed.
-
@MadScientist ok awesome! That really did help I wasn’t thinking of doubling them up in the terminal.
-
https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F191903753580
This converter isn’t adjustable and it’s only 5.0 v would this work? -
https://www.ebay.com/itm/1PCS-DC-DC-LM2596-power-Supply-Buck-Converter-step-down-module-NEW-CA/142147326064?hash=item2118a41070:g:L1kAAOSwvzRXzOBg
or
https://www.ebay.com/itm/DC-DC-Buck-Step-down-Regulator-Converter-4-2-23v-to-3V-3-3V-5V-9V-12V-24V-Module/112472493337?hash=item1a2fe20d19:g:dCsAAOSwdd9aVjD6
should do. They are adjustable via a potentiometer. Iam using the latter one for a Pi Zero but the 3A are enough to power a Pi3 easily. You should check aliexpress.com since most of the low priced parts already come from China. They will be even cheaper and are the very same product. -
How do these look?
http://s.aliexpress.com/67rmau6V?
http://s.aliexpress.com/vuaEjyAR? -
Yeah, that should do.
-
before i buy a power supply i wanted to ask if the one i had for it would work, if i spliced the adapter into it?
-
Sure it works. I just proposed the other one because it’s very compact and I thought that was important. Use the once you already have to save costs as long as it suits you. It’s powerful enough if those values are correct.
Especially those black power bricks can be of very bad quality. Run your mirror setup for a few hours and check that the power supply isn’t getting too hot.
-
My problem with it was that I didn’t want to have the brick of it out side the case. Or 3 foot of wire looped inside but I’ll have to cut it to add the step down anyway. So I may as well try it that way first. But I also didn’t know if it was big enough for both To run off of.
-
i ran into this problem awhile back but got put on the backburner.
-
@The-Bean Whats the buck down converter? I guess the pi is just a to big load for it
Never expect those china buck down converters to achieve more than 50% of what they say they will do (especially without additional cooler)
-
@The-Bean you might want to try with a additional cooler on the converter since the pi is not constantly pulling 2A, so it might work
-
-
@The-Bean When it gets really hot I would try with a heatsink
and what happens when you connect it and then turn up the voltage until you reach 5V? -
the converter its self doesnt really get hot.(that i have noticed) it just the wire to the pi. and once it drops, it doesnt adjust anymore.
-
hm strange I mean I don’t know the cable size you use, but 5V 2A is pretty much nothing for any cable. Should not really get hot for sure
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login