@sdetweil my code looks like this, perhaps it’s a need for an update…?

@snille Hi, trying to use this module but getting below error.
I followed your instructions i hope :-)
[07.01.2022 17:10.13.062] [ERROR] (node:30547) UnhandledPromiseRejectionWarning: TypeError: Cannot read properties of undefined (reading ‘body’)
at /home/pi/MagicMirror/modules/MMM-homeassistant-sensors/node_helper.js:40:83
at runMicrotasks ()
at processTicksAndRejections (node:internal/process/task_queues:96:5)
[07.01.2022 17:10.13.067] [ERROR] (node:30547) UnhandledPromiseRejectionWarning: Unhandled promise rejection. This error originated either by throwing inside of an async function without a catch block, or by rejecting a promise which was not handled with .catch(). To terminate the node process on unhandled promise rejection, use the CLI flag --unhandled-rejections=strict (see https://nodejs.org/api/cli.html#cli_unhandled_rejections_mode). (rejection id: 46)

Wow, thanks for sharing this!!!
Now, I’m back on track again :-)

Hi,

I’m using mmm-hue-lights and want to display temperature and/or the last motion from a Philips Hue motion sensor (indoor and outdoor).
Anyone added that feature…?

/Mikael

@jorgnyg i’ve tried to upload again but still not working :-(

@devmil Hi Michael, i’ve been testing with d-c-fix mirror-effect privacy film and acrylic oneway mirror and both is interfering the PIR sensor so i had to put in a small box above the frame. Not a fancy design though…
For the acrylic i have spare place beneath the screen so i drilled a hole.
For the upcoming bath mirror i’ve ordered a Pilkington MirrorView. Don’t know yet if it will work with the sensor behind that glass though…otherwise i’ll put in a separate place/box. Hard to drill the glass and wouldn’t dare trying :-|

@sdetweil :rolling_on_the_floor_laughing:
Yes, i’ve built two mirrors and now working on my third bathroom mirror and with x number of files open in Notepad++ it’s getting messy…and even if you can see the file name and it’s location (host name) you end up editing elsewhere :dizzy_face:

@hedmik sorry, my bad, i was editing config in another pi…
Now it’s working now as it should :-)

More or less the same problem for me…
I’m using a velleman VMA314 connected to GPIO pin 11 (BCM GPIO 17) and module MMM-PIR-Sensor.
I’ve updated wiringPi for Pi 4 (wiringPi updated to 2.52 for the Raspberry Pi 4B)
I see that state changes using “gpio readall” but nothing happens…or to start with, connected screen does not even turn off after time set in config:

		{
			module: 'MMM-PIR-Sensor',
			config: {
			// See 'Configuration options' for more information.
				sensorPin: 17, // The pin (BCM numbering, NOT pin number itself) your PIR-sensor is connected to.
				powerSaving: true, // Should the monitor be turned off if no user is present? (via HDMI or relay)
				powerSavingDelay: 5, // Additional software side delay (in seconds) before the monitor will be turned off.
				powerSavingNotification: true, // To display a notification before to switch screen off
				powerSavingMessage: "Skärmen stängs av på grund av inaktivitet..." // Message notification to display before to switch screen off
				
			}
		},

@sdetweil Hi again, and i’m very grateful for you helping me out :-)
Yes, i have both the standard and also a custom compliments module and by turning that custome module off MM is still running since one hour!!!
I’m so happy back on track again (cross my fingers) :-)
I will now focus on enhancing MMM-Telldus and MMM-Vastrafik modules.
I’ve also seen nice enhancements made for Weather forcast module (more descriptive text and translated to Swedish). Hope to get those enhancements otherwise i’ll do it mysfelf.
I’m also planning to develop a module for Engage (showing electricity consumption within the household).
Once again, big thanks!