Someone got it working on this post:
https://forum.magicmirror.builders/topic/11554/magicmirror-won-t-start-after-installing-module/6
hope this helps

@sdetweil

I did some digging around the net, and kinda got wifi working again. Wifi itself works fine. I can do sudo iwlist wlan0 scan, and see surrounding wifi. However the drop-down list on the panel does not work.
What i did to get my wifi working to this point was changing the /etc/network/interfaces file to

auto lo
iface lo inet loopback

auto eth0
iface eth0 inet dhcp

auto wlan0
allow-hotplug wlan0
iface wlan0 inet dhcp
        wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf

I found out I had some spelling errors like .config instead of .conf and found a default Buster Wpa_supplicant.conf file

here is my new Sudo ifconfig

eth0: flags=4163  mtu 1500
        inet 192.168.87.198  netmask 255.255.255.0  broadcast 192.168.87.255
        inet6 fe80::dea6:32ff:fe20:55bf  prefixlen 64  scopeid 0x20
        ether dc:a6:32:20:55:bf  txqueuelen 1000  (Ethernet)
        RX packets 1775  bytes 510729 (498.7 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 1633  bytes 972722 (949.9 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 275  bytes 80411 (78.5 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 275  bytes 80411 (78.5 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4163  mtu 1500
        inet 192.168.87.199  netmask 255.255.255.0  broadcast 192.168.87.255
        inet6 fe80::dea6:32ff:fe20:55c0  prefixlen 64  scopeid 0x20
        ether dc:a6:32:20:55:c0  txqueuelen 1000  (Ethernet)
        RX packets 20  bytes 2957 (2.8 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 32  bytes 5653 (5.5 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

Everything works, even ethernet, except for the wifi drop-down menu (shown below)

If I hover the mouse over it it says “connection to dhcpcd lost”
If I click on it, it says “No wireless interfaces found”
Can not really find anymore answers to this problem.
Have i disabled something somewhere?

Now that i look this post through, I saw that rfkill says “wlan”. Is it possible, that my Pi looks for wlan0 and not wlan, and therefore not being able to find it?

I guess I have to do that.
I have used a lot of time compiling and makeing things forward/backwards compatible python wise. Is there a way to save and transfer that?

I can try and take a picture in Noobs Recovery and upload it.

In Noobs the is one with “32 bit” at the end, and that’s not the one i have have installed. My raspbian version in Buster, if that helps.
what I have:
Camera Enabled
SSH Enabled
VNC Enabled
SPI Disabled
I2C Enabled
Serial Port Disabled (greyed out)
1-wire Disabled
Remote GPIO Disabled

I also can’t select Wifi Country code. It keeps forgetting it after clicking on ok
If i do it through sudo raspi-config I get “Could not communicate with wpa_suppliant” followed with “There was an error running option I4 Change wi-fi Country”
This is what I got, when I run: dmesg | grep brcmfmac

Is this as it should be?
Thanks for helping me with this.

Story short. I had installed Raspbian [Full] 64bit via NOOBS on a Pi 4. later I had to use my Pi 3B+, as i couldn’t find the type-C charger. Worked fine. Today after half a year having the pi in the closet, i found out that the internet didn’t work on it. switched to pi 4. Same problem. If i hover the mouse over the wifi icon, I get the message “No wireless interfaces found”. Neither the Ethernet port or wifi works, however Bluetooth are able to turn on.
I see that other people have this problem too, and as i only have installed MagicMirror, I thought it would be alright to post it here, to see if other found a solution other that format and reinstall raspbian.

What I did try (without quotation marks, and after = is console output):
“Sudo ifup wlan0” =
wpa_suppliant: cannot read contents of /etc/wpa_suppliant/wpa_suppliant.config
run-parts: /etc/network/if-pre-up.d/wpasuppliant exited with return code 1
ifup: failed to bring up wlan0

“sudo ifdown wlan0” =
ifdown: interface wlan0 not configured

“sudo rfkill” =
ID TYPE DEVICE SOFT HARD
0 wlan phy0 unblocked unblocked
1 Bluetooth hci0 blocked unblocked

I will keep updated on how it goes.

@blaukon I saw your pictures, and I see the text is easy to see in daylight, but in the video, it’s kinda hard to see in low light. But how is it with your own eyes in brought daylight and with low light/night?

I have been looking around on this site, but I can’t seem to find what kind foil would be good to use.
Can those who have tried foil, describe what their experience is, and what kind of foil they used eg. what transparency it is, vendor, and name of the foil.

I have tried some mirrors, with an LCD monitor, but have come to only get too dim screen with the Pilkington chrome spy 6 mm, or I end ud seeing too much background light from the monitor (A monitor the school gave me for the projekt, which uses glass tubes as bagground light).
Do i have to use an OLED or what else combination do i need for it be good at a reasonable price?