{HowTo} turn on/off your monitor (Time based, PIR/Button, App)

teitlebot · Nov 27, 2018, 2:10 AM

@richland007 This wont be helpful but I will say I had a similar problem a few months back but now it works. Must be some configuration that changed in the mean time on my pi but I dont know what.

bolish · Jan 23, 2019, 12:43 PM

Hello there,

I’m currently planning my project and will integrate PIR sensor + related 2.1 method through HDMI.There is one thing confusing me :

we talk about HDMI CEC in method 2.1
nevertheless, it seems the PIR Sensor module is “only” turning HDMI output off and that is triggering "issues such as “powersaving / no input”.

But is HDMI CEC not allowing us to send a “turn screen off” command to the monitor instead of disabling the rasp. HDMIoutput and relying / hoping on the monitor’s behaviour?

Sorry once more if I mssed the point, but would like to understand before moving forward.

Regards

sdetweil · Jan 23, 2019, 3:41 PM

@bolish said in {HowTo} turn on/off your monitor (Time based, PIR/Button, App):

But is HDMI CEC not allowing us to send a “turn screen off” command to the monitor instead of disabling the rasp. HDMIoutput and relying / hoping on the monitor’s behaviour?

as I understand it, not many monitors/tv’s provide support for external power off/on commands…

none of my TV’s used for MM support this…

bolish · Jan 23, 2019, 3:41 PM

@sdetweil Maybe you’re right! I didn’t considered that.

But seems possible, correct? By changing the actual commands to the ones defined by the libcec librairy?

sdetweil · Jan 23, 2019, 3:52 PM

@bolish I do not know… as I said, none of my TVs support ANY commands to turn off/on…

in my MMM-SleepWake module, I use module.hide() to hide everything, leaving a blank screen… for those devices that do not provide external control…

bolish · Jan 24, 2019, 8:27 AM

OK, I will then try myself when I will receive my stuff and let forums knows if working or not.

chandra · Feb 26, 2019, 6:52 AM

@cruunnerr ,
Thank you very much for the detailed write up. As a beginner, i could follow the steps. I used the 2.1 Using PIR-Module. Its working well.
Few questions,
Now trying to connect LED strip-

should i remove the module from the config?
Or 2.2 Using PIR-script will work simultaneously?
I read your following post, But, can you help me how to implement all?

@cruunnerr said in {HowTo} turn on/off your monitor (Time based, PIR/Button, App):

In my Case I am using a RGB 5050 Stripe. I am using three pins with mosfets and for the software part PIGPIOD.

Just like that: https://dordnung.de/raspberrypi-ledstrip/

Here are my scripts:

monitor on:

vcgencmd display_power 1

pigs p 17 1
pigs p 22 1
pigs p 24 1

sleep 0.06s

pigs p 17 2
pigs p 22 2
pigs p 24 2

sleep 0.06s

pigs p 17 3
pigs p 22 3
pigs p 24 3

sleep 0.06s

pigs p 17 4
pigs p 22 4
pigs p 24 4

sleep 0.06s

pigs p 17 5
pigs p 22 5
pigs p 24 5

sleep 0.06s

pigs p 17 6
pigs p 22 6
pigs p 24 5

sleep 0.06s

pigs p 17 7
pigs p 22 7
pigs p 24 6

sleep 0.06s

pigs p 17 8
pigs p 22 8
pigs p 24 7

sleep 0.06s

pigs p 17 9
pigs p 22 9
pigs p 24 8

sleep 0.06s

pigs p 17 10
pigs p 22 10
pigs p 24 9

sleep 0.06s

pigs p 17 11
pigs p 22 11
pigs p 24 10

sleep 0.06s

pigs p 17 12
pigs p 22 12
pigs p 24 11

Monitor off:

pigs p 17 12
pigs p 22 12
pigs p 24 11

sleep 0.06s

pigs p 17 11
pigs p 22 11
pigs p 24 10

sleep 0.06s

pigs p 17 10
pigs p 22 10
pigs p 24 9

sleep 0.06s

pigs p 17 9
pigs p 22 9
pigs p 24 8

sleep 0.06s

pigs p 17 8
pigs p 22 8
pigs p 24 7

sleep 0.06s

pigs p 17 7
pigs p 22 7
pigs p 24 6

sleep 0.06s

pigs p 17 6
pigs p 22 6
pigs p 24 5

sleep 0.06s

pigs p 17 5
pigs p 22 5
pigs p 24 5

sleep 0.06s

pigs p 17 4
pigs p 22 4
pigs p 24 4

sleep 0.06s

pigs p 17 4
pigs p 22 4
pigs p 24 4

sleep 0.06s

pigs p 17 3
pigs p 22 3
pigs p 24 3

sleep 0.06s

pigs p 17 2
pigs p 22 2
pigs p 24 2

vcgencmd display_power 0

sleep 0.06s

pigs p 17 1
pigs p 22 1
pigs p 24 1

sleep 0.06s

pigs p 17 0
pigs p 22 0
pigs p 24 0

chandra · Feb 27, 2019, 4:41 PM

@cruunnerr said in {HowTo} turn on/off your monitor (Time based, PIR/Button, App):

Sure, my pir.py is the same as shown on point 2.2 but with other GPIO used

#!/usr/bin/env python

import sys
import time
import RPi.GPIO as io
import subprocess
import pigpio

io.setmode(io.BCM)
SHUTOFF_DELAY = 119 # seconds
PIR_PIN = 25       # 22 on the board
LED_PIN = 16

def main():
    io.setup(PIR_PIN, io.IN)
    io.setup(LED_PIN, io.OUT)
    turned_off = False
    last_motion_time = time.time()

    while True:
        if io.input(PIR_PIN):
            last_motion_time = time.time()
            io.output(LED_PIN, io.LOW)
            print ".",
            sys.stdout.flush()
            if turned_off:
                turned_off = False
                turn_on()
        else:
            if not turned_off and time.time() > (last_motion_time + 
                                                 SHUTOFF_DELAY):
                turned_off = True
                turn_off()
            if not turned_off and time.time() > (last_motion_time + 1):
                io.output(LED_PIN, io.HIGH)
        time.sleep(.1)

def turn_on():
        subprocess.call("sh /home/pi/lights_on.sh", shell=True)

def turn_off():
        subprocess.call("sh /home/pi/lights_off.sh", shell=True)

if __name__ == '__main__':
    try:
        main()
    except KeyboardInterrupt:
        io.cleanup()

Because i use some LED Stripes which turn on when the pir detects movement my “monitor_on.sh” is called “lights_on.sh”

lights_on.sh:

vcgencmd display_power 1

pigs p 17 1
pigs p 22 1
pigs p 24 1

sleep 0.06s

pigs p 17 2
pigs p 22 2
pigs p 24 2

sleep 0.06s

pigs p 17 3
pigs p 22 3
pigs p 24 3

sleep 0.06s

pigs p 17 4
pigs p 22 4
pigs p 24 4

sleep 0.06s

pigs p 17 5
pigs p 22 5
pigs p 24 5

sleep 0.06s

pigs p 17 6
pigs p 22 6
pigs p 24 5

sleep 0.06s

pigs p 17 7
pigs p 22 7
pigs p 24 6

sleep 0.06s

pigs p 17 8
pigs p 22 8
pigs p 24 7

sleep 0.06s

pigs p 17 9
pigs p 22 9
pigs p 24 8

sleep 0.06s

pigs p 17 10
pigs p 22 10
pigs p 24 9

sleep 0.06s

pigs p 17 11
pigs p 22 11
pigs p 24 10

sleep 0.06s

pigs p 17 12
pigs p 22 12
pigs p 24 11

lights_off.sh:

pigs p 17 12
pigs p 22 12
pigs p 24 11

sleep 0.06s

pigs p 17 11
pigs p 22 11
pigs p 24 10

sleep 0.06s

pigs p 17 10
pigs p 22 10
pigs p 24 9

sleep 0.06s

pigs p 17 9
pigs p 22 9
pigs p 24 8

sleep 0.06s

pigs p 17 8
pigs p 22 8
pigs p 24 7

sleep 0.06s

pigs p 17 7
pigs p 22 7
pigs p 24 6

sleep 0.06s

pigs p 17 6
pigs p 22 6
pigs p 24 5

sleep 0.06s

pigs p 17 5
pigs p 22 5
pigs p 24 5

sleep 0.06s

pigs p 17 4
pigs p 22 4
pigs p 24 4

sleep 0.06s

pigs p 17 4
pigs p 22 4
pigs p 24 4

sleep 0.06s

pigs p 17 3
pigs p 22 3
pigs p 24 3

sleep 0.06s

pigs p 17 2
pigs p 22 2
pigs p 24 2

vcgencmd display_power 0

sleep 0.06s

pigs p 17 1
pigs p 22 1
pigs p 24 1

sleep 0.06s

pigs p 17 0
pigs p 22 0
pigs p 24 0

But what exactly doesn’t work with my script? Maybe i can help :)

Got this ( https://dordnung.de/raspberrypi-ledstrip/) working successfully on another raspberry running stretch.

now going to try this on Magicmirror. But i got confused, because PIR sensor is on GPIO22 and the same GPIO22 is used in led strip (5050).
Can you guide , which GPIO to be assigned?

sdetweil · Feb 27, 2019, 4:42 PM

@chandra move one to a different GPIO pin and change the config as required for that

chandra · Feb 27, 2019, 4:57 PM

@sdetweil said in {HowTo} turn on/off your monitor (Time based, PIR/Button, App):

@chandra move one to a different GPIO pin and change the config as required for that

thank you, but as i mentioned, i’m just a beginner. just copying and pasting.:face_with_stuck-out_tongue_winking_eye:
So lets fix led on GPIO22 and move PIR to another.