Read the statement by Michael Teeuw here.
PIR-Sensor - put your mirror to sleep if not used
-
@KirAsh4 didn’t think about that. Oops
-
Hello,
I’ve installed this module and sensor to my pi but I’m facing an issue.
When I start the app, its loading as expected and show everything normally.
After 5 sec. my monitor goes to sleep and says me “no signal” even if I shake may hand front of it.
Then monitor blink a few times and seems like open but nothing to show or said.
After this situation, never comes to live back and can’t close or shut down the app (can’t go back to OS screen). I have to shut the power to reset my pi.Do you have any idea why this happens?
-
Any ETA on when the update will occur for removing the wiring-pi dependency? I wouldn’t like going down to a lower version of Node.js for this to work encase I break the whole thing.
-
Sorry no :/ I just started a new job/school and I do not currently have a mirror setup :( but it should really not be that hard to do so feel free to just try! You can use onoff there is an example which would not need to be changed much to replace wiring Pi in my code :)
If you succeed please send a pull request!Edit: If I find some time this evening I will try to do it but you will have to test as again I don’t have a mirror currently.
-
Double post so you get notified: Done feel free to try :) don’t forget to reinstall the module with
npm install! -
@paviro So it works with node 6 now?
-
@Mitchfarino if it still works at all yes :)
-
Now it should definitely work :)
-
I have the same issue. Does anybody have a solution for this problem?
-
I´m playing around with PIR and after reinstalling npm it seems to work.
the only problem is that my monitor is switching on and off every couple of seconds.
do you guys have a picture of how your sensor is setup (Poti, Trigger Jumper)?thanks a lot!
-
Hi,
i have some issue with the PIR Module. It worked for testing a couple of month but now under productive operation it doesn’t :(
The Screen is switched off and on correctly but after a unspecified time it doesn’t switch it on anymore, it stays black. Sometimes after an hour sometimes after a couple of minutes.
The PIR itself is working correctly as i discovered, i’m also getting it’s state under FHEM and there i can see the relaible functionality of it. I connected it to the GPIO 21.
As i can see on the screen it doesn’t get any video input anymore. Only rebooting the PI2 will fix it.
I’m not sure where to search :(
Some startup log entrie doesn’t show anything.
> magicmirror@2.0.0 start /home/pi/MagicMirror > electron js/electron.js Loading config ... Loading module helpers ... Initializing new module helper ... Initializing new module helper ... No helper found for module: alert. No helper found for module: clock. Initializing new module helper ... No helper found for module: compliments. No helper found for module: currentweather. No helper found for module: weatherforecast. Initializing new module helper ... All module helpers loaded. Starting server op port 8080 ... Server started ... Connecting socket for: MMM-FHEM Connecting socket for: MMM-PIR-Sensor Connecting socket for: calendar Starting node helper for: calendar Connecting socket for: newsfeed Starting module: newsfeed Sockets connected & modules started ... Launching application. -
Thanks for the module - this is fantastic!
I have a PIR sensor attached and it works as desired, but when the HDMI signal is cut to the TV, I get a “No Signal” message on the screen from the TV itself because the RPi isn’t sending signal anymore.
I’m wondering what the best solution would be. My head goes to hiding all modules instead of turning the monitor off so MM is still on but a completely black screen, or somehow send the RPi into a sleep state but keep the HDMI active.
Has anyone else tackled this issue?
-
@phrazelle The idea behind it is so that when the HDMI is disabled you would get the no signal. You then set up the TV/Monitor to go to sleep if no signal is found.
Check your TV manual for power saving settings. -
@McSorley Thanks for the response!
Unfortunately my TV doesn’t have a sleep mode option. It automatically displays the No Signal message and turns off after a few minutes of no signal. To make that more difficult, if the TV is turned back on with the remote, it loses the resolution settings and blows everything up until the RPi is rebooted.
I’m not sure how to address this, but I think it would be ideal in my circumstance to have this module, but triggered by the PIR sensor. Idk if I can finagle that, but I suppose I can give it a shot.
-
Do we still have this problem with the node version? (v5 works, 6 not)
-
@phrazelle hi! did you find a way to disable this message? i have the same annoying one :)
-
@bibi Yes! Here is the post I submitted around the new module. Remember that you still need the MMM-PIR-Sensor module by paviro installed for this to work.
-
@phrazelle interesting! thx a lot will check this :)
-
-
Nevermind, I’m back on the white page problem… It keeps saying “Error: Module version mismatch. Expected 50, got 51”
I tried either: npm rebuild --runtime=electron --target=1.4.0 --disturl=https://atom.io/download/atom-shell --build-from-source
and: npm rebuild --runtime=electron --target=1.4.5 --disturl=https://atom.io/download/atom-shell --abi=50but it doesn’t change…
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login