MagicMirror Forum
    • Recent
    • Tags
    • Unsolved
    • Solved
    • MagicMirror² Repository
    • Documentation
    • 3rd-Party-Modules
    • Donate
    • Discord
    • Register
    • Login
    A New Chapter for MagicMirror: The Community Takes the Lead
    Read the statement by Michael Teeuw here.

    Motion Detection with RaspiCam, Non-Module version

    Scheduled Pinned Locked Moved Tutorials
    47 Posts 13 Posters 46.8k Views 17 Watching
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • bheplerB Offline
      bhepler Module Developer
      last edited by bhepler

      Hrm. New problem: After a few hours, the screen goes white. This obviously will not do. Back to the drawing board.

      I found this in the motion log:

      [1] [NTC] [ALL] [Nov 15 20:25:02] motion_loop: End of event 74
      [1] [NTC] [ALL] [Nov 15 20:25:04] motion_loop: fps: 3.999920 idle 26.67% over 0.00%
      [1] [NTC] [ALL] [Nov 15 20:25:09] motion_loop: fps: 3.998465 idle 24.89% over 0.00%
      [1] [ERR] [ENC] [Nov 15 20:25:10] ffmpeg_put_frame: Error while writing video frame:
      [1] [NTC] [ALL] [Nov 15 20:25:10] motion_loop: Thread exiting
      [1] [INF] [ALL] [Nov 15 20:25:10] motion_cleanup: Calling vid_close() from motion_cleanup
      [1] [INF] [VID] [Nov 15 20:25:10] vid_close: calling video source cleanup
      [1] [ALR] [VID] [Nov 15 20:25:10] MMAL Camera cleanup
      [0] [NTC] [ALL] [Nov 15 20:25:11] main: Threads finished
      [0] [NTC] [ALL] [Nov 15 20:25:12] main: Motion terminating
      [0] [NTC] [ALL] [Nov 15 20:25:12] motion_remove_pid: Removed process id file (pid file).
      [0] [NTC] [ALL] [Nov 15 20:25:12] motion_remove_pid: Closing logfile (/tmp/motion.log).
      
      1 Reply Last reply Reply Quote 0
      • bheplerB Offline
        bhepler Module Developer
        last edited by bhepler

        I believe I have it cracked. The white screen was due to MMAL Motion crashing whilst writing a frame to disk. When Motion crashes, it apparently jacks up the video output.

        My current solution is to use PM2 to monitor the motion process and restart it when necessary. I’m testing now. If it works for a few more days I’ll report back.

        Adding motion to PM2: pm2 start motion. Be sure that the motion is not configured to run as a daemon (first option in config file).

        lolobyteL 1 Reply Last reply Reply Quote 1
        • lolobyteL Offline
          lolobyte @bhepler
          last edited by lolobyte

          @bhepler

          Hi, i do the same at first and restor my sw installation.
          But after the same procedure of sw installation this error was again on top.

          I resolve, by my sw, the reason for that was: motion must start after pm2 startin mm.

          My mm start’s automaticly after rebooting.
          My motion also. => collision of SW.

          By doing motion in an cron job with delay time al was fun an running as iwant.

          in my case i do following:
          don’t foget to install screen.

          sudo apt-get intsall screen

          My motion is running in a screen session.
          then the cronjob

          crontab -e

          and set motion with following parameters:

          @reboot sleep 150; screen -S motion -dmS sudo motion -c /home/pi/motion/motion-mmalcam.conf

          i hope this is helpfull for you and other persons here.

          B 1 Reply Last reply Reply Quote 1
          • bheplerB Offline
            bhepler Module Developer
            last edited by

            Update: Having PM2 monitor the motion process seems to work quite well. However, I have now discovered that there is a memory leak somewhere in all of this. Using the MMM-SystemStats module, I can watch free memory trickle down throughout the day.

            I’ve configured the Pi to reboot early each morning. That’s not an ideal situation, but it seems to have solved the problem. Good enough for me! And more importantly, good enough for the gift recipient.

            lolobyteL 1 Reply Last reply Reply Quote 0
            • lolobyteL Offline
              lolobyte @bhepler
              last edited by

              @bhepler

              have u increase the swapfile?

              bheplerB 1 Reply Last reply Reply Quote 0
              • bheplerB Offline
                bhepler Module Developer @lolobyte
                last edited by

                @lolobyte Negative, I have not. What would you recommend?

                lolobyteL 1 Reply Last reply Reply Quote 0
                • lolobyteL Offline
                  lolobyte @bhepler
                  last edited by lolobyte

                  @bhepler
                  in general it’s not bad for a raspi3 to increase the swapfile from 100MB to a higher level.

                  at first check your status:
                  sudo service dphys-swapfile status
                  U see something like this:

                  ● dphys-swapfile.service - LSB: Autogenerate and use a swap file
                  Loaded: loaded (/etc/init.d/dphys-swapfile)
                  Active: active (exited) since Mi 2016-11-30 13:17:14 CET; 6h ago
                  Process: 613 ExecStart=/etc/init.d/dphys-swapfile start (code=exited, status=0 /SUCCESS)

                  Nov 30 13:17:13 raspi3 systemd[1]: Starting LSB: Autogenerate and use a swa…
                  Nov 30 13:17:14 raspi3 dphys-swapfile[613]: Starting dphys-swapfile swapfile…
                  Nov 30 13:17:14 raspi3 dphys-swapfile[613]: want /var/swap=1024MByte, checki…t
                  Nov 30 13:17:14 raspi3 dphys-swapfile[613]: done.
                  Nov 30 13:17:14 raspi3 systemd[1]: Started LSB: Autogenerate and use a swap…e.
                  Hint: Some lines were ellipsized, use -l to show in full.

                  Maybe u have 100MB instead of 1024 like in my case.

                  If u want to change this value the edit your

                  sudo nano /etc/dphys-swapfile

                  change to this value and save your file

                  CONF_SWAPSIZE=1024

                  the do a

                  sudo dphys-swapfile setup

                  and activate your new swap level:

                  sudo dphys-swapfile swapon

                  thats all. Now your System can handle wit more than his physical RAM.

                  In My case i do in raspi-config a new

                  “Expand File system”

                  to reorganize the file system an reboot after that my raspi.
                  If you are a owner of a raspi 2 it’s more common to change the swap file to max 512MB.

                  please inform me what’s your experience after this change

                  you can also check very niche your tasks mem, swap and other things in a ssh session on your PC with htop

                  sudo apt-get install htop

                  have a nice try

                  1 Reply Last reply Reply Quote 0
                  • B Offline
                    Binog @lolobyte
                    last edited by

                    @lolobyte
                    Can U specify what this command does,. Am not sure if it isn’t doubling the motion command:

                    @reboot sleep 150; screen -S motion -dmS sudo motion
                    (ignored the -c path part, cause renamed the config to motion.conf, so not needed)

                    why is there two time motion - in it?

                    By the way it isn’t working on my mirror

                    1 Reply Last reply Reply Quote 0
                    • KimzerK Offline
                      Kimzer
                      last edited by

                      I am completely unable to make this work.
                      The camera wont take any snapshots, maybe just a config error. But can someone confirm that this still works or show me something that works? Dont wanna go out and buy a pir sensor if i can make use of the raspicam. :)

                      bheplerB 1 Reply Last reply Reply Quote 0
                      • bheplerB Offline
                        bhepler Module Developer @Kimzer
                        last edited by

                        @Kimzer - If the camera won’t even take a snapshot, then none of this is going to work. Have you tried the various tutorials about getting the PiCam to work? The ones that are at the basic level of “I enter this command and it takes a picture right then and there and I can download it”?

                        Start with the official Getting Started Guide. Once you can get images from the camera to your Pi, come back.

                        If you can get the camera to produce images but have trouble getting Motion to work, follow my tutorial and the part where it says “at this point you can test it but…”, stop there. Change the parameter in the motion.conf file named output_pictures to on and change on_event_start to echo Motion Detected!. That should put a bunch of snapshots on your memory card. Test Motion by entering ./motion -c motion.conf and you should see motion writing messages to the screen.

                        1 Reply Last reply Reply Quote 0
                        • 1
                        • 2
                        • 3
                        • 4
                        • 5
                        • 1 / 5
                        • First post
                          Last post
                        Enjoying MagicMirror? Please consider a donation!
                        MagicMirror created by Michael Teeuw.
                        Forum managed by Sam, technical setup by Karsten.
                        This forum is using NodeBB as its core | Contributors
                        Contact | Privacy Policy