PIR Sensor turning display on/off over and over

elmerito25

Same here. I verified all the connections and tested using the same script and it keeps printing “Motion detected!” Did you play around with the jumpers on your PIR? I am still trying to figure out if my PIR is defective.

strawberry 3.141

@elmerito25 I don’t have a mirror to test, but the code does the following

from gpiozero import MotionSensor

pir = MotionSensor(4)

while True: #repeat this forever
    if pir.motion_detected: # if motion is detected print the message
        print("Motion detected!")

after the print is done it immediately repeats the loop, because their is no sleep, timeout, delay or whatsoever in there. So for me the expected behaviour is that it prints over and over the same message. You could try to check motion not detected

from gpiozero import MotionSensor
import time

pir = MotionSensor(4)

while True: #repeat this forever
    if pir.motion_detected: # if motion is detected print the message
        print("Motion detected!")
    if not pir.motion_detected: # if no motion is detected print the message
        print("No motion detected!")
    time.sleep(1)

run this and leave your sensor alone it will print just every second

hermlam

I have the same issue. Maybe it’s related to WiFi. I tested the PIR with on older PI 2, no WiFi. Ran the Python script, working perfectly.
After installing the PIR to my Mirror Pi, a Pi 3 screen wouldn’t go out. Installed the test Python script again and I am getting a lot of false positives, over 5 a minute. So PIR stays highs and screen stays on.
I am thinking that WiFi is interfering with the PIR.
Anybody any experiences or ideas?

Thanks,
Herman

fischi87

by my mirror it works really nice. i have a question, it is possible the time to change right now it turns the display off after 4 minutes. i would like to change the time maybe 2 minutes or so.

thanks

Renfield

It might be interference. Try installing a ferrite bead. The person whose site I’ve linked below had a very similar problem and describes how he fixed it.

https://helentronica.com/2016/01/11/magic-mirror-with-motion-detector/

Renfield

cowboysdude

@Renfield said in PIR Sensor turning display on/off over and over:

It might be interference. Try installing a ferrite bead. The person whose site I’ve linked below had a very similar problem and describes how he fixed it.

https://helentronica.com/2016/01/11/magic-mirror-with-motion-detector/

Renfield

It’s what I had to do with mine… they are very inexpensive…

elmerito25

@cowboysdude said in PIR Sensor turning display on/off over and over:

@Renfield said in PIR Sensor turning display on/off over and over:

It might be interference. Try installing a ferrite bead. The person whose site I’ve linked below had a very similar problem and describes how he fixed it.

https://helentronica.com/2016/01/11/magic-mirror-with-motion-detector/

Renfield

It’s what I had to do with mine… they are very inexpensive…

Thanks guys! Will try this once I get home tonight!

elmerito25

@elmerito25 said in PIR Sensor turning display on/off over and over:

@cowboysdude said in PIR Sensor turning display on/off over and over:

@Renfield said in PIR Sensor turning display on/off over and over:

It might be interference. Try installing a ferrite bead. The person whose site I’ve linked below had a very similar problem and describes how he fixed it.

https://helentronica.com/2016/01/11/magic-mirror-with-motion-detector/

Renfield

It’s what I had to do with mine… they are very inexpensive…

Thanks guys! Will try this once I get home tonight!

Thanks @Renfield and @cowboysdude ! Followed your advice and found a ferrite bead on unused USB cable and got the PIR sensor working perfectly!

Renfield

Great to hear. I love it when a plan comes together.

Now I need to scrounge up a bead for my build.
Ren

hermlam

Hi all,
Thanks for the reactions. I ordered one and will test tomorrow.
Herman