Electron CPU usage

[martinkooij]

@mattn and others.
I have a stable situation with the following:

• electron 1.4.15 (withELECTRON_FORCE_WINDOW_MENU_BAR=1).
  higher elektron version gives black screen, the environment variable lowers the cpu-usage by elektron considerably).
• Magic Mirror 2.3.1 (actually I was quick to install MM2.3.0 but manually downgraded electron, but I am quite sure that amounts to the same as installing MM 2.3.1).
• nodejs version v9.11.1. (I used to have a 1.6.x nodejs, but that one caused memory leaks. )

Is now running in this configuration almost 7 days without interrupt. And no signs of stopping soon. Thanks you all in this forum for the help.

(Rasberry pi 3, Jessie, CPU Hardware: BCM2835, Revision: a02082)

[cdelaorden]

Hi guys

Im new to the forum and this project but I have some small experience with the Pis and having the same issue

I think that its related to the video driver, using ‘sudo raspi-config’ and changing the video driver to one of the GL drivers resulted in a much lower cpu load in my case.

Doesn’t matter if you choose full KMS or fake KMS as long as you dont use the legacy non-GL driver.

It took my 4 CPU from full 100% to idle bellow 35%

Im sure someone else with this problem can confirm this

[E3V3A]

@cdelaorden

• How can we check the video driver without using rapsi-conf?
  in dmesg? in systemd journal?
• How/where do you set the: ELECTRON_FORCE_WINDOW_MENU_BAR=1.
• What would be the easiest way for users to check electron version from command line?

[cdelaorden]

@e3v3a
You can check it in the config.txt

or just do a “tail /boot/config.txt | grep dtoverlay” to check what version is enabled

all the rest of my configuration is the default one after a fresh install from the current version of MM and Raspbian, I havent touched anything from electron

[Juju]

Omg, yes finally! :D
First I followed this installation guide: https://forum.magicmirror.builders/topic/236/complete-setup-tutorial/3
I had the electron CPU issue. So I downgraded to electron version 1.4.15. The CPU usage went down from 90% to 70%. It was still laggy as hell.
I then formatted the microSD card and followed that youtube guide: https://www.youtube.com/watch?v=0Q04SKvibik
Downgraded to 1.4.15 again and now it’s running great with a CPU usage of like 5% with spikes to 50%, when there is an animation on the screen.

But I have one question.

After I finished the youtube tutorial I have the “MagicMirror” and the “mm”. Both autostart when I boot the raspberry pi.
Which use has the “mm”?

[Mykle1]

@juju

pm2 stop mm
pm2 delete mm
pm2 save
rm ~/mm.sh

[MichMich]

@cdelaorden I think you’ve found the issue! Awesome work!

For others please note that when you start raspi-config and go to “Advanced Options” > “GL Driver”, the top one will always be selected, no matter which one is active. After selecting one of the two top drivers (GL), it might solve the hi CPU load issue …

It solved it on a clean installed Pi 3 for me.

[MichMich]

I added some info about the Open GL driver to the Wiki:
https://github.com/MichMich/MagicMirror/wiki/Configuring-the-Raspberry-Pi#enable-the-open-gl-driver-to-decrease-electrons-cpu-usage

[Hein-Jan]

@michmich

I seem to be running into some kind if trouble. My SD card failed, so I had to do a clean install. I decided to immediately go for the full KMS driver.
“$ tail /boot/config.txt | grep dtoverlay” results in “dtoverlay=vc4-kms-v3d”.

The CPU usage is alright, but “/home/pi/.pm2/logs/mm-error-o.log” states:

libGL error: MESA-LOADER: failed to retrieve device information
MESA-LOADER: failed to retrieve device information
MESA-LOADER: failed to retrieve device information

I am having trouble with the monitor. I am using MMM-Remote-Control.
“MONITOROFF” results in “/home/pi/.pm2/logs/mm-error-o.log”:

Powering off HDMI

“MONITORON” results in “/home/pi/.pm2/logs/mm-error-o.log”:

Powering on HDMI with preferred settings

[E] Failed to power on HDMI with preferred settings

{ Error: Command failed: tvservice --preferred && sudo chvt 6 && sudo chvt 7
[E] Failed to power on HDMI with preferred settings

    at ChildProcess.exithandler (child_process.js:217:12)
    at emitTwo (events.js:106:13)
    at ChildProcess.emit (events.js:194:7)
    at maybeClose (internal/child_process.js:899:16)
    at Process.ChildProcess._handle.onexit (internal/child_process.js:226:5)
  killed: true,
  code: null,
  signal: 'SIGTERM',
  cmd: 'tvservice --preferred && sudo chvt 6 && sudo chvt 7' }
Powering off HDMI

I may be wrong but I feel this is related to the Full KMS driver.

Can anyone confirm? Does anyone have a solution?
I am way out of my depth here…

[Dom1n1c]

@Hein-Jan I got the same issue.
A few minutes, the monitor could be controlled, but then “tvservice -p” fails to power on the monitor.