Electron CPU usage

E3V3A

How can we check the video driver without using rapsi-conf?
in dmesg? in systemd journal?
How/where do you set the: ELECTRON_FORCE_WINDOW_MENU_BAR=1.
What would be the easiest way for users to check electron version from command line?

cdelaorden

@e3v3a
You can check it in the config.txt

or just do a “tail /boot/config.txt | grep dtoverlay” to check what version is enabled

all the rest of my configuration is the default one after a fresh install from the current version of MM and Raspbian, I havent touched anything from electron

Juju

Omg, yes finally! :D
First I followed this installation guide: https://forum.magicmirror.builders/topic/236/complete-setup-tutorial/3
I had the electron CPU issue. So I downgraded to electron version 1.4.15. The CPU usage went down from 90% to 70%. It was still laggy as hell.
I then formatted the microSD card and followed that youtube guide: https://www.youtube.com/watch?v=0Q04SKvibik
Downgraded to 1.4.15 again and now it’s running great with a CPU usage of like 5% with spikes to 50%, when there is an animation on the screen.

But I have one question.

After I finished the youtube tutorial I have the “MagicMirror” and the “mm”. Both autostart when I boot the raspberry pi.
Which use has the “mm”?

Mykle1

@juju

pm2 stop mm
pm2 delete mm
pm2 save
rm ~/mm.sh

MichMich

@cdelaorden I think you’ve found the issue! Awesome work!

For others please note that when you start raspi-config and go to “Advanced Options” > “GL Driver”, the top one will always be selected, no matter which one is active. After selecting one of the two top drivers (GL), it might solve the hi CPU load issue …

It solved it on a clean installed Pi 3 for me.

MichMich

I added some info about the Open GL driver to the Wiki:
https://github.com/MichMich/MagicMirror/wiki/Configuring-the-Raspberry-Pi#enable-the-open-gl-driver-to-decrease-electrons-cpu-usage

Hein-Jan

@michmich

I seem to be running into some kind if trouble. My SD card failed, so I had to do a clean install. I decided to immediately go for the full KMS driver.
“$ tail /boot/config.txt | grep dtoverlay” results in “dtoverlay=vc4-kms-v3d”.

The CPU usage is alright, but “/home/pi/.pm2/logs/mm-error-o.log” states:

libGL error: MESA-LOADER: failed to retrieve device information
MESA-LOADER: failed to retrieve device information
MESA-LOADER: failed to retrieve device information

I am having trouble with the monitor. I am using MMM-Remote-Control.
“MONITOROFF” results in “/home/pi/.pm2/logs/mm-error-o.log”:

Powering off HDMI

“MONITORON” results in “/home/pi/.pm2/logs/mm-error-o.log”:

Powering on HDMI with preferred settings

[E] Failed to power on HDMI with preferred settings

{ Error: Command failed: tvservice --preferred && sudo chvt 6 && sudo chvt 7
[E] Failed to power on HDMI with preferred settings

    at ChildProcess.exithandler (child_process.js:217:12)
    at emitTwo (events.js:106:13)
    at ChildProcess.emit (events.js:194:7)
    at maybeClose (internal/child_process.js:899:16)
    at Process.ChildProcess._handle.onexit (internal/child_process.js:226:5)
  killed: true,
  code: null,
  signal: 'SIGTERM',
  cmd: 'tvservice --preferred && sudo chvt 6 && sudo chvt 7' }
Powering off HDMI

I may be wrong but I feel this is related to the Full KMS driver.

Can anyone confirm? Does anyone have a solution?
I am way out of my depth here…

Dom1n1c

@Hein-Jan I got the same issue.
A few minutes, the monitor could be controlled, but then “tvservice -p” fails to power on the monitor.

cdelaorden

@hein-jan @Dom1n1c

Please use the fake kms driver instead “dtoverlay=vc4-fkms-v3d”

it its known that the full kms driver isnt compatible with tvservice plus other restrictions

EDIT:
Also with the fake KMS you can rotate the display from /boot/config.txt so I suggest @michmich using it as the preferred method in the wiki

schmo90

@cdelaorden said in Electron CPU usage:

the full kms driver isnt compatib

hy now i use the fake kms driver, everything is working fine and realy fast.
but i have the problem that the mirror will go to a black screen after some hours.

only a pm2 restart mm helps in this case -.-