Hello-Lucy

cowboysdude

@TheGeekfather Try using a Omnidirectional mic… like this :
https://www.walmart.com/ip/Stereo-Omnidirectional-Condenser-Microphone-Mic-3-5mm-Connector-for-Meeting-Business-Conference-Desktop-Computer/392379431

Can’t say it will solve the delay…the Pi’s seem to have that delay…

alt text

Mykle1

@cowboysdude

You are absolutely right, CBD. That microphone extends the active listening distance dramatically. Across the room without shouting and it improves the success of the commands.Thanks for recommending it to me. I’m going to get another. :thumbsup:

@TheGeekfather

Yes, I just finish testing Lucy on a Pi 4, with a usb microphone and with a usb sound card that accepts an analog microphone. In both cases, the latency is pretty annoying. And even though you (and I) were using an analog microphone, the presence of the USB adapter slows things up. The usb microphone by itself was just as slow.

Now, take that same analog microphone and use it on a 12+ year old laptop board running ubuntu and MM with Lucy. The response is measured in milliseconds. It’s fantastic!

doctorwhen

@Mykle1 I added a few modules to Hello-Lucy following your easy instructions. Not sure if this is the best way to contact you with the info but just following through with the last step in your instructions which is to tell you the command and module name :)

Here is a diff of my sentences.json and yours:

80,81d79
< "HIDE IFRAME",
< "SHOW IFRAME",
86,87d83
< "HIDE LIGHTS",
< "SHOW LIGHTS",
92,93d87
< "HIDE NETWORK",
< "SHOW NETWORK",
108,109d101
< "HIDE SOLAR",
< "SHOW SOLAR",
116,117d107
< "HIDE STOCKS",
< "SHOW STOCKS",

And a diff of my checkCommands.json and yours:

7,21d6
<   ["SHOW","IFRAME","","","true","MMM-iFrame",""],
<   ["HIDE","IFRAME","","","false","MMM-iFrame",""],
<
<   ["SHOW","LIGHTS","","","true","mmm-hue-lights",""],
<   ["HIDE","LIGHTS","","","false","mmm-hue-lights",""],
<
<   ["SHOW","NETWORK","","","true","MMM-NetworkScanner",""],
<   ["HIDE","NETWORK","","","false","MMM-NetworkScanner",""],
<
<   ["SHOW","SOLAR","","","true","MMM-Solar",""],
<   ["HIDE","SOLAR","","","false","MMM-Solar",""],
<
<   ["SHOW","STOCKS","","","true","MMM-stocks",""],
<   ["HIDE","STOCKS","","","false","MMM-stocks",""],
<
124,125c109,110
<   ["SHOW","STATS","","","true","MMM-SystemStats",""],
<   ["HIDE","STATS","","","false","MMM-SystemStats",""],
---
>   ["SHOW","STATS","","","true","MMM-PC-Stats",""],
>   ["HIDE","STATS","","","false","MMM-PC-Stats",""],
145,148c130,133
<   ["SHOW","WEATHER","","","true","currentweather",""],
<   ["HIDE","WEATHER","","","false","currentweather",""],
<   ["SHOW","WEATHER","","","true","weatherforecast",""],
<   ["HIDE","WEATHER","","","false","weatherforecast",""]
---
>   ["SHOW","WEATHER","","","true","MMM-BMW-DS",""],
>   ["HIDE","WEATHER","","","false","MMM-BMW-DS",""],
>   ["SHOW","WEATHER","","","true","MMM-NOAA3",""],
>   ["HIDE","WEATHER","","","false","MMM-NOAA3",""]

As you can see, I added support for the following modules:
MMM-iFrame, mmm-hue-lights, MMM-NetworkScanner, MMM-Solar, and MMM-stocks

I also modified your existing support for the STATS and WEATHER commands, altering them to act upon different modules.

Thanks for the really cool module and easy instructions to extend!

Mykle1

@doctorwhen said in Hello-Lucy:

Thanks for the really cool module and easy instructions to extend!

You’re welcome. I tried to make the installation instructions as clear as possible. You have just confirmed that for me, so thank you.

I went ahead and added your modifications to the repo so that they now work by default for anyone that cares to use Lucy.

Many thanks!

Mykle1

Hello-Lucy.

Minor Update

Add 4 more modules to the defaults:

MMM-EveryNews
MMM-MercuryInRetrograde
MMM-PLOW
MMM-WeatherOrNot

Bringing the total of modules that now work by default to 58

amsuvarna27

@Mykle1
I have installed Hello Lucy.
My microphone and speakers are working correctly.
And Hello Lucy logo also appears on the magic mirror screen,But when I give command like Hello Lucy it won’t respond.
Only temperature module is showing and not working.
I’m using Raspberry pi 3 B plus model.

Mykle1

@amsuvarna27

So, Hello-Lucy does not show either? You should see a microphone icon with the words “Say, Hello Lucy” next to it.

Did you complete all 3 installation steps in the readme?

Using the default config? You would still need to install those modules. Using other than the default modules you would have to follow the directions in the “How to add modules to Hello-Lucy” file included in the clone of Lucy AND install those modules. Have you done that?

What is the result of arecord -l in your terminal? (That’s a lower case L)

Lastly, post your config entry for Hello-Lucy in a code block so I can see it. All modules in the config must be installed separately for Lucy to control them. This is one of mine:

{
            disabled: false,
            module: "Hello-Lucy",
            position: "top_center",
            config: {
                keyword: 'HELLO LUCY', // keyword to activate listening for a command/sentence
                timeout: 15, // timeout listening for a command/sentence
                standByMethod: 'DPMS', // 'DPMS' = anything else than RPi or 'PI'
                microphone: "0,0", // run "arecord -l" card # and device # mine is "0,0"
                sounds: ["1.mp3", "11.mp3", "a.mp3", "best.mp3", "c.mp3", "1.mp3", "listening.mp3", "me2.mp3", "nice.mp3", "weather.mp3"], // welcome sound at startup. Add several for a random choice of welcome sound
                confirmationSound: "ding.mp3", // name and extension of sound file
                startHideAll: true, // All modules start as hidden EXCEPT PAGE ONE
                // *** Page One is your default startup page *** This overrides startHideAll: true,
                pageOneModules: ["Hello-Lucy", "MMM-EasyPix"], // default modules to show on page one/startup
                pageTwoModules: ["Hello-Lucy", "MMM-BMW-DS", "MMM-EventHorizon"], // modules to show on page two
                pageThreeModules: ["Hello-Lucy", "MMM-Lunartic"], // modules to show on page three
                pageFourModules: ["Hello-Lucy", "MMM-PC-Stats"], // modules to show on page four
                pageFiveModules: ["Hello-Lucy", "MMM-Searchlight"], // modules to show on page five
                pageSixModules: ["Hello-Lucy", "MMM-NOAA3"], // modules to show on page six
                pageSevenModules: ["Hello-Lucy", "MMM-Nascar"], // modules to show on page seven
                pageEightModules: ["Hello-Lucy", "MMM-rfacts"], // modules to show on page eight
                pageNineModules: ["Hello-Lucy", "MMM-History"], // modules to show on page nine
                pageTenModules: ["Hello-Lucy", "MMM-HardwareMonitor"] // modules to show on page ten
            }
        },

Mykle1

Hello Lucy!

amsuvarna27

@Mykle1
I have installed Hello Lucy.
My microphone and speakers are working correctly.
And Hello Lucy logo also appears on the magic mirror screen,But when I give command like Hello Lucy it won’t respond.
Only temperature module is showing and not working.
I’m using Raspberry pi 3 B plus model.

rrussis82

How would I be able to add the ability to hide all modules if the trigger word isn’t spoken after a determined amount of time, say 2 minutes? Then I can issue the voice command to show all modules to wake it.

I’ve tried using a pi-camera to detect motion to turn on the screen and turn off the screen, but i get the “HDMI not connected” symbol and the pi-camera is flaky where it doesn’t always work. I’ve tried multiple modules for the camera and don’t like any of them, as they can create multiple instance of the camera opening and then cause it lock up. I like how you can hide all modules to blank screen by voice command without disconnecting the HDMI output. until I can figure out a way to do this with motion, I’d like to be able to do this automatically, like a time-out.

I’ve tried-MMM-NotificationTrigger to try to fire the HIDE_MODULE notification in your code, but I have not successfully found a decent notification trigger to make it happen. If i get a USB Webcam in the future maybe i can use motion as a trigger to fire the notification, but like I said, i haven’t had luck using motion on the pi-cam so i doubt i would on a webcam.

Also for page navigation, I like to use MMM-Carousel by shbatm, the navigation buttons to go from one page to the other will be instrumental to when I add touch ability to my mirror, so i set up Hello-Lucy with just one page showing MMM-Carousel, is there anyway to incorporate voice activation on Hello-Lucy to work with changing the pages on MMM-Carousel? I think they are called slides on MMM-Carousel.