[Electron] display en screen after installing MMM-PIR-Sensor

[RIKKO14]

And I forgot to not the IP adress of my py, so I can’t use ssh now…
Pffff, I’m not lucky, every modules I want works instead of the PIR module…

[RIKKO14]

If i find my IP adress, Can you give me the commands to delete the problem ?

[sdetweil]

@RIKKO14 if u didn’t turn on ssh, it isn’t on, so can’t use it anyhow. look in your router to see what addresses were given out…

I do that quite often, then fix/reserve the address so I don’t have to remember

[RIKKO14]

ok, i find my IP adress (I’ve wrote it in excel file with some commandes i use) and I connected in SHH with putty,
thanks for your help to delete the commandh whose powered off my screen

[RIKKO14]

below my pm2 logs,
If that can help you…
https://www.cjoint.com/c/JHvqsqJ1QTT

[RIKKO14]

If it can help you this is my pm2 logs : https://www.cjoint.com/c/JHvqsqJ1QTT

[sdetweil]

@RIKKO14 looking at… hard to tell
do

pm2 stop 0
pm2 flush 
pm2 start 0

the will throw away the old logs…

[RIKKO14]

I do this, the problem still here…

[sdetweil]

@RIKKO14 it just makes the log easier to read. please post it again

[RIKKO14]

hre it is :
https://www.cjoint.com/c/JHvrPBCBgZT

[RIKKO14]

and this one (because i don’t if it it change something) : https://www.cjoint.com/c/JHvrUegIVzT after the command :

pm2 stop 0
pm2 flush 
pm2 start 0

and after only pm2 logs --lines=100

without pm2 status and pm2 stop 0

[sdetweil]

@RIKKO14 i see this
0|mm | [2020-08-21 19:37:58.395] [LOG] [LPCM16] WARN: arecord: pcm_read
:2145: erreur en lecture: Appel système interrompu
and this
0|mm | [2020-08-21 19:43:41.435] [LOG] [Error: failed to read sensor]

so we may have to look at t he browser dev window,
ctrl-shift-i on the mirror keyboard
select the tab labebled console,
and scroll up to see any errors, usually in red text

[RIKKO14]

ctrl+shift+i on the mirror keyboard : nothing displayed
ctrl+shift+i on my pc keyboard : this is displayed :

[RIKKO14]

ctrl+shift+i on the mirror keyboard : nothing displayed : because my screen is powered off : source of the issue…

[sdetweil]

@RIKKO14 too small to read

[sdetweil]

@RIKKO14 i think the ‘failed to read the sensor’ error lead to the power off command being issued…

but don’t know

[RIKKO14]

https://www.cjoint.com/c/JHvsIkBBC7T

[sdetweil]

@RIKKO14 that is dev window open on forum page, not MM page

[RIKKO14]

that’s te problem…
you ask me to do ctrl+shift+i on the mirror keyboard :
but the screen is powered off so nothing displayed, i don’t know if it’s displayed something, I can’t see it…
or i don’t anderstand to acceed MM page with my pc, I have only this :

[sdetweil]

@RIKKO14 edit the config.js on the mirror

change address and ipWhitelist like this

address:"0.0.0.0",
ipWhitelist:[],

restart mm…

now on your pc you can do
http://pi_ip:8080

and then u can open the dev window on that page

i thought you said earlier you had removed the command to make your mirror screen turn off
so you know which code is issuing the command… tell where that was