Bathroom Magic Mirror Cabinet "Alibert" - MagicAlibert

[spitzlbergerj]

Hi,
and again I have finished a bathroom MagicMirror. This time it should be a mirror cabinet by special request, in Germany one says often “Alibert” to this kind of bathroom mirror. And so the MagicAlibert was born.

The principle of my MagicMirror you can see in this post.
You can also find the sources for mirror glass and accessories there.

Exterieur

Interieur

Parts, milled

Parts, Flat dowel

Parts, system 32 holes

Hinge holes

Hinges nearly closed

Hings open

Shell clamped

Shell finished

With back wall

wall mounts

Hole for cable

Body with doors

right door with cutout for screen

left door without cutout

back plane for right door

back plane for right door

doors closed

after painting

hinge

3D prints for left door - bracket glass insert - bracket cross bar

3D prints for left door - bracket glass insert - bracket cross bar

3D prints for left door - bracket glass insert - bracket cross bar

Screen built in

all technic installed

all technic installed

mounted back panel right door

Handles and bracket mounted to hold up the heavy doors

Handles and bracket mounted to hold up the heavy doors

left door open

right door open

finished - ready to moun

I have used:

• Raspberry pi 3
• Beech wood from the hardware store
• Aluminium composite panel (ACP) with cutout (https://www.plattenzuschnitt24.de/ - german: Alu Dibond Platte)
• Spy mirror (https://www.glas-star.de/spionspiegelnachmass/chrome-spy-spiegel/)
• Silicone (PCI Silcofern S) Color: black (Important! Never use transparent silicone. Otherwise you will see it and regret it!)
• Screen (HP 24w (1CA86AA) 60,45 cm (23,8 Zoll) monitor (IPS, Full HD, HDMI)
• Radar motion detector (Amazon Haljia 5 RCWL-0516)

You find a 3D model here

If you want to know more, then ask ;-)

Regards
Josef

[sdetweil]

@spitzlbergerj really awesome!!

[Zoltan]

I really like the two door idea

Really neat woodwork

[oli28]

I love the Bring! App, just had to google for it :D

[cowboysdude]

@spitzlbergerj this is by far the best bathroom mirror I have seen!! Excellent job and tutorial!

[spitzlbergerj]

@sdetweil, @Zoltan, @cowboysdude Thanks for your compliments

[nickthebeer]

@spitzlbergerj that’s is really cool, I might make one of these for home when we change our bathroom suite. What’s the toilet roll etc on the display for?

[spitzlbergerj]

@nickthebeer

What’s the toilet roll etc on the display for

Hi, thats the module for the bring list app: https://github.com/rseidt/MMM-bringList
;-)

[Binog]

Hey, Great Work !
Can You post a picture from the back !?
And maybe a picture from the interior (counted from the last one, a picture between 4 and 5 so how You mounted the pi, etc…)
Thx !

[spitzlbergerj]

Hi @binog ,
here is a picture of the back

The wiring still has to be done. This is only the temporary solution. The cords you can see on the photo are currently used for stabilization, because the MagicAlibert is very “door-heavy”.

I can only provide a picture of the mounted Raspberry Pi later, when I have removed the back of the door again.

[Binog]

@spitzlbergerj
thx !!

[OberfragGER]

@spitzlbergerj Great work and finish.
Where did u attach the Haljia 5 RCWL-0516) an which Modul are u using for that sensor?

[spitzlbergerj]

@OberfragGER
Thanks for the compliments!
I will put the radar sensor outside the body either on top or on the bottom. I have printed a white housing for it with the 3D printer, which I can mount accordingly. Let’s see where it responds better

[cyberphox]

That’s next level stuff right there! Great job!

[spitzlbergerj]

@cyberphox Thanks for the compliments!

[spitzlbergerj]

Hi everybody,

and here are the photos of the interior of the right door:

The screen is already fixed through the cutout of the Alu Dibond plate. With a little tape it is actually already fixed enough. For safety I have attached 4 angles, which press it additionally in. The Raspberry is mounted on a 3D printed plate. The cable routing is done via damp room cable boxes.

right door - interieur

right door - interieur

[spitzlbergerj]

Hi all,

you could find a 3D model here

Regards
Josef

[lxne]

Awesome work!
Are the mirrors just glued onto the doors?
And did you use the chrome spy for both sides?

Best wishes,
Alex (Lower Bavaria)

[spitzlbergerj]

@lxne Thanks!
yes they are just glued
you see my method of glueing better in this post https://forum.magicmirror.builders/topic/9154/bathroom-magic-mirror
No, I don’t use chrome spy, I bought the mirrors here https://www.glas-star.de/spionspiegelnachmass/chrome-spy-spiegel/