[MMM-Remote-Control] Can not access remote control module

motdog · Mar 4, 2019, 1:11 AM

@Mykle1 my bad. I am confusing on this. I did a fresh reboot of the whole thing using Jesse instead of Raspian stretch and don’t have the start up issues. I rebuilt the config like I wanted with all of the modules working good. I then add the remote module and change the address etc and get the please make a config file error. As soon as I remove the remote control info things work again. So I know the error comes when I add this module. The frustrating thing is at a previous point I was able to get the remote control module working. That’s why I am confused but here is my working config without remote control.

Thanks for your patience with me on this



var config = {
	address: "localhost", // Address to listen on, can be:
	                      // - "localhost", "127.0.0.1", "::1" to listen on loopback interface
	                      // - another specific IPv4/6 to listen on a specific interface
	                      // - "", "0.0.0.0", "::" to listen on any interface
	                      // Default, when address config is left out, is "localhost"
	port: 8080,
	ipWhitelist: ["127.0.0.1", "::ffff:127.0.0.1", "::1"], // Set [] to allow all IP addresses
	                                                       // or add a specific IPv4 of 192.168.1.5 :
	                                                       // ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.1.5"],
	                                                       // or IPv4 range of 192.168.3.0 --> 192.168.3.15 use CIDR format :
	                                                       // ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.3.0/28"],

	language: "en",
	timeFormat: 12,
	units: "imperial",

	modules: [
		{
			module: "alert",
		},
		{
			module: "updatenotification",
			position: "top_bar"
		},
		{
			module: "clock",
			position: "top_left"
		},
		{
			module: "calendar",
			position: "top_left",
			config: {
				calendars: [
					
{
						symbol: "calendar-check",
						url: "http://kuathletics.com/calendar.ashx/calendar.ics?sport_id=4&schedule_id=0&_=dd9bfb6f-df5f-4a47-9975-dd3bb74bd06a"
					},

					{
						symbol: "calendar-check",
						url: "https://calendar.google.com/calenxxxxxxxxxxx7495e80bc22/basic.ics"
					},

					{
						symbol: "calendar-check",
						url: "http://ical-cdn.tex3xxxxxxxxxx4e056117.ics"
					},

					{
						symbol: "calendar-check",
						url: "http://ical-cdn.teamsnap.com/team_schedule/xxxxxxxxxxa68b.ics"
					}
				]
			}
		},

		{
			module: "compliments",
			position: "lower_third"
		},

			{
	        module: 'MMM-NOAA3',
		position: 'bottom_left',
	        config: {
			    provider: "darksky", 
			    apiKey: "6462c3f6d7c6dxxxxx311",         
			    airKey: "WZzmCBxxxxxmBM",    
		        css: "NOAA4",                    
			userlat: "x8.7xx9",  
		        userlon: "-x0.5xx" 
	 }
         },



		{
			  module: "MMM-NowPlayingOnSpotify",
			  position: "bottom_right",
			
			  config: {
			    clientID: "85d8bxxxxxxx",
			    clientSecret: "e6b226e4b819xxxxxx",
			    accessToken: "Bxxxi-UItbKL3NR1dQXpC8sJ1041J5NjVeafoAb3fGVsicRUataJodmfa1urp0akDwThbo",
			    refreshToken: "AQBP1w70KP5TqlxiFNgA4RU6mdTct0AHb58nasw2sEpl17iIz-uPDq9M0ifITQcOxxxxxx"
			  }
},



		{
			  module: "MMM-MyScoreboard",
			  position: "top_right",
			  classes: "default everyone",
			  header: "My Scoreboard",
			  config: {
			    showLeagueSeparators: true,
			    colored: true,
			    viewStyle: "mediumLogos",
			    sports: [
			      {
			        league: "NHL",
			        teams: ["STL"]
			      },
			      {
			        league: "NBA",
			        teams: ["BOS", "GS", "HOU", "PHI"],
			        
			      },
			      {
			        league: "MLB",
				teams: ["STL"]
			        
			      },
			      {
			        league: "NFL",
			        
			      },
				
				
			      {
			        league: "NCAAM",
			        groups: ["Top 25"]
			      }
			   
			    ]
			
			  }
			},



		{
			module: "currentweather",
			position: "top_right",
			config: {
				location: "New York",
				locationID: "",  //ID from http://bulk.openweathermap.org/sample/; unzip the gz file and find your city
				appid: "YOUR_OPENWEATHER_API_KEY"
			}
		},
		{
			module: "weatherforecast",
			position: "top_right",
			header: "Weather Forecast",
			config: {
				location: "New York",
				locationID: "5128581",  //ID from https://openweathermap.org/city
				appid: "YOUR_OPENWEATHER_API_KEY"
			}
		},
		{
			module: "newsfeed",
			position: "bottom_bar",
			config: {
				feeds: [
					{
						title: "New York Times",
						url: "http://www.nytimes.com/services/xml/rss/nyt/HomePage.xml"
					}
				],
				showSourceTitle: true,
				showPublishDate: true
			}
		},
	]

};

/*************** DO NOT EDIT THE LINE BELOW ***************/
if (typeof module !== "undefined") {module.exports = config;}

sdetweil · Mar 4, 2019, 2:20 AM

@motdog whenever you get the ‘create a config file’ error, run

npm run check:config

and work thru the errors from the top down

Mykle1 · Mar 4, 2019, 2:44 AM

@motdog

I went and installed MMM-Remote-Control on a laptop running ubuntu and MM v2.5.0. I used this config entry:

The module loads (bottom right):

I’ll send a picture from my other machine. brb

Mykle1 · Mar 4, 2019, 2:53 AM

@motdog

You can clearly see that it is working remotely.

It would not allow connection with address: "localhost",. Take your working config and carefully add my entry for Remote-Control, address and ipWhitelist It should work.

motdog · Mar 4, 2019, 3:54 PM

@Mykle1 Awesome! Thanks so much for your help.

Mykle1 · Mar 5, 2019, 4:13 AM

@motdog

So, does that mean that it’s working for you now? If so, mark the topic as solved.

AshDarko · Mar 5, 2019, 12:49 AM

Hi, i too have the same issue. I have changed my router IP to be something other than 192.XXX.X.XX

Could this be the problem? I can access via browser on the Pi…?

When i run the remote in browser on the pi, i notice in terminal this message:

MMM-Remote-Control customMenu Requested, but file:/home/pi/MagicMirror/config/custom_menu.json was not found

i receive an “Access Denied to IP address 10.100.10.1” in terminal and a message on m y phone saying the device is not allowed to access your mirror

Here is config code:

address: "0.0.0.0", // Address to listen on, can be:
	                      // - "localhost", "127.0.0.1", "::1" to listen on loopback interface
	                      // - another specific IPv4/6 to listen on a specific interface
	                      // - "", "0.0.0.0", "::" to listen on any interface
	                      // Default, when address config is left out, is "localhost"
	port: 8080,
	ipWhitelist: [ "127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:10.100.10.0/24",], // Set [] to allow all IP addresses
	                                                       // or add a specific IPv4 of 192.168.1.5 :
	                                                       // ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.1.5"],
	                                                       // or IPv4 range of 192.168.3.0 --> 192.168.3.15 use CIDR format :
	                                                       // ["127.0.0.1", "::ffff:127.0.0.1", "::1", "::ffff:192.168.3.0/28"],

	language: "en",
	timeFormat: 24,
	units: "metric",

And here is my module code:

{
		module: 'MMM-Remote-Control',
		/**position: 'bottom_left',**/
		config: {
			customCommand: {},  // Optional, See "Using Custom Commands" below
			customMenu: "custom_menu.json", // Optional, See "Custom Menu Items" below
			showModuleApiMenu: true, // Optional, Enable the Module Controls menu
			/**apiKey: "",         // Optional, See API/README.md for details**/
		}
	},

The module code is pretty much the defaults.

AshDarko · Mar 5, 2019, 12:51 AM

I have just commented out the custom menu for now, so ignore that terminal message about it

{
		module: 'MMM-Remote-Control',
		/**position: 'bottom_left',**/
		config: {
			customCommand: {},  // Optional, See "Using Custom Commands" below
			/**customMenu: "custom_menu.json", // Optional, See "Custom Menu Items" below**/
			showModuleApiMenu: true, // Optional, Enable the Module Controls menu
			/**apiKey: "",         // Optional, See API/README.md for details**/
		}
	},

motdog · Mar 5, 2019, 4:13 AM

@Mykle1 my only other question is when I was at a friend’s house I tried to pull up the remote to show them the mirror & nothing happened on their wifi or cellular. I’m guessing on the white list I would have to input my phone ip address?

sdetweil · Mar 5, 2019, 3:18 PM

@motdog lot more than that…

by default your home router blocks ALL incoming requests (or should anyhow) so you would have to open a port and map incoming requests on that port to your mirror machine (and port) by using the routers admin function… some providers do not allow this
(this is called port forwarding)

second, the IP address of the router on the internet is assigned dynamically, and might change…
some of us use a dns mapper to define a specific NAME to our router as it appears on the internet
( I use dyndns.org to map a known name to my router ip address, today my routers internet ip address is near 47.220.177.xxx)

third, the ip address of your phone will be randomly assigned too… their router, maybe over phone link connection… so , here u might have to say 0.0.0.0 anyone…