Read the statement by Michael Teeuw here.
MMM-PIR-Sensor - White Screen
-
yes but i dont have the folder node_modules in the PIR Folder :/ i have install WrinPi but nothing works :/
-
ok so lets go step by step:
cd ~/MagicMirror/modules/now we will remove the PIR folder:
rm -rf MMM-PIR-Sensorand from here, we’re going to reinstall the MMM-PIR-Sensor modul:
git clone https://github.com/paviro/MMM-PIR-Sensor.git
cd MMM-PIR-Sensorrun the following cmd here:
npm installand wait, this can take a few minutes.Now you’ll have to add pi to gpio
sudo useradd -g pi gpioand reboot your Raspi:
sudo rebootYou’ll have to connect your PIR Sensor the right way with your Raspi.
I’ve connected my PIR Sensor on the following Pins:
I’ve got a Pi2 and use Pin 2 for power, Pin 6 for Ground and Pin 15 for Data.
– correctin grn pin
and dont forget to add the config :-)
-
you are the best !! i dont become no a with screen !
but the sensor dont work
i have
vcc: Pin 2
Data: Pin 7
Ground: Pin 6and my config in the config and MMM-PIR-Sensor data is:
} { module: 'MMM-PIR-Sensor', config: { sensorPIN: 7, relayPIN: false, powerSaving: true, relayOnState: 1, } },the sensetiv is max and the time is min
Note from admin: Please use Markdown on code snippets for easier reading!
-
If you use pin 7 in your config its nr 4
You have to use the gpio nr.
-
Thank you it works fine !!
-
@Bangee I tried everything regarding the white screen issues. I’m a noob. was able to get magic mirror installed, I also installed the PIR motion detection and can confirm motion is detected.
Downgraded Node JS
Installed the electron
made sure module was added in config.jsI am using the Raspberry PI 3 mode b.
Can somebody confirm this module is working with Raspberry Pi 3.
Any help would be greatly appreciative…
Thanks. -
can you restart the magicmirror an check what errormessage you have:
pm2 logs mm -
@Bangee Thank you so much for responding. I removed magic mirror completely reinstalled… then installed the module.
All is well now… Thank you so much!
-
@Bangee hi ! thx for your nice tuto, i have proceed with it but i got a warning as below:
pi@raspberrypi:~/MagicMirror/modules/MMM-PIR-Sensor $ npm install
npm WARN prefer global npm@3.10.9 should be installed with –g
do i have to do smt specific or it’s just ok to leave it without any action?
ps: my config file is also not working with PIR module implemented… maybe that is the reason? thx you very much for any feedabck guys!! -
@bibi did you try it with the instructions from paviro:
https://github.com/paviro/MMM-PIR-SensorI don’t think that this warn is your problem. I have so many times these warnings :-D
You sould send us whats in yourpm2 logs mm -
@Bangee yes i follow his and yours… quite the same… regarding this npm warning I do nothing then as understood?
I will send you the log later when I’m home
Thx bangee! Appreciated! -
@Bangee so as expected the pm2 log mm just show that the file has syntax error… here is my config file, i put the module at the end…
thx again :) -
@bibi
powerSaving: true -
@strawberry-3.141 right was a typo but still the config file is “not created” :((
-
@bibi can you post your whole config file?
-
@strawberry-3.141 here you go and many thx in advance - i struggling with this now (sorry i don’t know why only few parts of the code is with the color background)
/* Magic Mirror Config Sample * * By Michael Teeuw http://michaelteeuw.nl * MIT Licensed. */ var config = { port: 8080, language: 'en', timeFormat: 24, units: 'metric', modules: [ { module: 'alert', }, { module: 'clock', position: 'top_left' }, { module: 'calendar', header: 'US Holidays', position: 'top_left', config: { calendars: [ { symbol: 'calendar-check-o ', url: 'webcal://www.calendarlabs.com/templates/ical/US-Holidays.ics' } ] } }, { module: 'compliments', position: 'lower_third' }, { module: 'currentweather', header: 'xxx', position: 'top_right', config: { location: 'xxx,xxx', locationID: 'xxx', //ID from http://www.openweathermap.org appid: 'xxx' } }, { module: 'newsfeed', position: 'bottom_bar', config: { feeds: [ { title: "New York Times", url: "http://www.nytimes.com/services/xml/rss/nyt/HomePage.xml" }, ], showSourceTitle: true, showPublishDate: true }, { module: 'MMM-PIR-Sensor', config: { sensorPIN: 22, powerSaving: true } }, ] }; /*************** DO NOT EDIT THE LINE BELOW ***************/ if (typeof module !== 'undefined') {module.exports = config;}
Note from admin: Please use Markdown on code snippets for easier reading!
-
Everything with at least one tab indent is treated as code and highlighted. ;)
-
@yawns thx! :))
-
@bibi you forgot to close the config section in the newsfeed module, add
}aftershowPublishDate: trueand you should be fine -
@strawberry-3.141 yeah! thx a lot. at least i can see this white screen now :p :))) have to figure out how to solve this… Only if it’s realllllly really obvious for you/someone, i post my log file. (sorry to ask so much) otherwise not prob, i will reinstall the PIR module…
[TAILING] Tailing last 10 lines for [mm] process (change the value with --lines option) /home/pi/.pm2/logs/mm-error-0.log last 10 lines: 0|mm | at Error (native) 0|mm | at process.module.(anonymous function) [as dlopen] (ELECTRON_ASAR.js:168:20) 0|mm | at Object.Module._extensions..node (module.js:583:18) 0|mm | at Object.module.(anonymous function) [as .node] (ELECTRON_ASAR.js:168:20) 0|mm | at Module.load (module.js:473:32) 0|mm | at tryModuleLoad (module.js:432:12) 0|mm | at Function.Module._load (module.js:424:3) 0|mm | at Module.require (module.js:483:17) 0|mm | at require (internal/module.js:20:19) 0|mm | at bindings (/home/pi/MagicMirror/modules/MMM-PIR-Sensor/node_modules/bindings/bindings.js:76:44) /home/pi/.pm2/logs/mm-out-0.log last 10 lines: 0|mm | No helper found for module: clock. 0|mm | Initializing new module helper ... 0|mm | No helper found for module: compliments. 0|mm | No helper found for module: currentweather. 0|mm | No helper found for module: weatherforecast. 0|mm | Initializing new module helper ... 0|mm | Whoops! There was an uncaught exception... 0|mm | MagicMirror will not quit, but it might be a good idea to check why this happened. Maybe no internet connection? 0|mm | If you think this really is an issue, please open an issue on GitHub: https://github.com/MichMich/MagicMirror/issues 0|mm | Launching application.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login