• Recent
  • Tags
  • Unsolved
  • Solved
  • MagicMirror² Repository
  • Documentation
  • 3rd-Party-Modules
  • Donate
  • Discord
  • Register
  • Login
MagicMirror Forum
  • Recent
  • Tags
  • Unsolved
  • Solved
  • MagicMirror² Repository
  • Documentation
  • 3rd-Party-Modules
  • Donate
  • Discord
  • Register
  • Login
A New Chapter for MagicMirror: The Community Takes the Lead
Read the statement by Michael Teeuw here.

No sound from my RPi 3 B.

Scheduled Pinned Locked Moved Solved Troubleshooting
16 Posts 4 Posters 5.2k Views 3 Watching
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • S Offline
    sdetweil @sdetweil
    last edited by Apr 16, 2019, 1:50 AM

    @sdetweil do system sounds work?

    Sam

    How to add modules

    learning how to use browser developers window for css changes

    1 Reply Last reply Reply Quote 0
    • B Offline
      BillW @sdetweil
      last edited by Apr 16, 2019, 1:51 AM

      @sdetweil No

      1 Reply Last reply Reply Quote 0
      • S Offline
        sdetweil
        last edited by sdetweil Apr 16, 2019, 1:52 AM Apr 16, 2019, 1:52 AM

        https://www.raspberrypi.org/documentation/configuration/audio-config.md

        Sound is going out the HDMI cable

        Sam

        How to add modules

        learning how to use browser developers window for css changes

        1 Reply Last reply Reply Quote 0
        • B Offline
          BillW
          last edited by Apr 16, 2019, 1:54 AM

          I’ll follow the link and check it out, then I’ll let you know what I did. Thanks for the guidance.

          S 1 Reply Last reply Apr 16, 2019, 2:22 AM Reply Quote 0
          • S Offline
            sdetweil @BillW
            last edited by Apr 16, 2019, 2:22 AM

            @BillW this one too

            https://www.cb-net.co.uk/linux/getting-analogue-sound-working-raspberry-pi-3b-raspbian-stretch/

            Sam

            How to add modules

            learning how to use browser developers window for css changes

            1 Reply Last reply Reply Quote 0
            • B Offline
              BillW
              last edited by Apr 16, 2019, 2:45 AM

              Ok, tried all three but no luck, not sure what to do next. Here’s a copy of my config file if that may help

              For more options and information see

              http://rpf.io/configtxt

              Some settings may impact device functionality. See link above for details

              uncomment if you get no picture on HDMI for a default “safe” mode

              #hdmi_safe=1

              uncomment this if your display has a black border of unused pixels visible

              and your display can output without overscan

              #disable_overscan=1

              uncomment the following to adjust overscan. Use positive numbers if console

              goes off screen, and negative if there is too much border

              #overscan_left=16
              #overscan_right=16
              #overscan_top=16
              #overscan_bottom=16

              uncomment to force a console size. By default it will be display’s size minus

              overscan.

              #framebuffer_width=1280
              #framebuffer_height=720

              uncomment if hdmi display is not detected and composite is being output

              #hdmi_force_hotplug=1

              uncomment to force a specific HDMI mode (this will force VGA)

              #hdmi_group=1
              #hdmi_mode=1

              uncomment to force a HDMI mode rather than DVI. This can make audio work in

              DMT (computer monitor) modes

              #hdmi_drive=2

              uncomment to increase signal to HDMI, if you have interference, blanking, or

              no display

              #config_hdmi_boost=4

              uncomment for composite PAL

              #sdtv_mode=2

              #uncomment to overclock the arm. 700 MHz is the default.
              #arm_freq=800

              Uncomment some or all of these to enable the optional hardware interfaces

              #dtparam=i2c_arm=on
              #dtparam=i2s=on
              #dtparam=spi=on

              Uncomment this to enable the lirc-rpi module

              #dtoverlay=lirc-rpi

              Additional overlays and parameters are documented /boot/overlays/README

              Enable audio (loads snd_bcm2835)

              #dtparam=audio=on
              [pi0]
              dtoverlay=dwc2
              [all]
              start_x=1
              gpu_mem=128
              dtoverlay=googlevoicehat-soundcard
              display_rotate=1

              Sorry for the large font, not well verse with the editing portion of this forum.

              S 1 Reply Last reply Apr 16, 2019, 3:32 AM Reply Quote 0
              • S Offline
                sdetweil @BillW
                last edited by sdetweil Apr 16, 2019, 3:33 AM Apr 16, 2019, 3:32 AM

                @BillW use the markdown 3 backticks before and after… key to the left of number 1

                you can edit it… pound sign makes large font

                my device doesn’t have an analog audio port

                Sam

                How to add modules

                learning how to use browser developers window for css changes

                1 Reply Last reply Reply Quote 0
                • B Offline
                  BillW
                  last edited by Apr 17, 2019, 12:13 AM

                  My knowledge of this is very limited, I don’t understand where you want me to put the markdown at?

                  S B M 3 Replies Last reply Apr 17, 2019, 1:20 AM Reply Quote 0
                  • S Offline
                    sdetweil @BillW
                    last edited by Apr 17, 2019, 1:20 AM

                    @BillW edit your previous post.

                    In front of the content you pasted in, on a separate line, put three backtics

                    Then go to the end of the content you pasted, add a new line and put three backtics there. Submit your post update

                    Sam

                    How to add modules

                    learning how to use browser developers window for css changes

                    1 Reply Last reply Reply Quote 0
                    • B Offline
                      bhepler Module Developer @BillW
                      last edited by Apr 17, 2019, 2:02 AM

                      @BillW - You can find the markdown commands at this link. Please use them to post code, file contents and commands.

                      1 Reply Last reply Reply Quote 0
                      • 1
                      • 2
                      • 1 / 2
                      1 / 2
                      • First post
                        9/16
                        Last post
                      Enjoying MagicMirror? Please consider a donation!
                      MagicMirror created by Michael Teeuw.
                      Forum managed by Sam, technical setup by Karsten.
                      This forum is using NodeBB as its core | Contributors
                      Contact | Privacy Policy