@Fonfon ok i find after 2 hours :)
at the end bottom
after
crtl x
y
enter
sudo reboot

rotate_display=1 90°
rotate_display= 3 270°

@broberg Crap, that’s another problem! Now I gotta worry about bulb hours, and burn in, since there’s a good chance that the same info will be in the same places all the time.

@johnnyboy

.MMM-WunderGround table.small td:nth-child(5), .MMM-WunderGround table.small td:nth-child(6) { /* do the magic */ }

@cowboysdude said in What magic mirror module blew your mind?:

As was I… referring to there’s not much config needed

So, what’s it called? MMM-Voice? MMM-VoiceControl? Something else?

@RedNax I say yes! And Great job!

Does anyone know the company Canviz ? They do a fairly similar thing to the magic mirror, (although the content that they display is different) - mostly pictures, animation, and things. However, they just decided to share their frame building tutorial for free! Also - if you are struggling with building a frame (and you have a 21.5" monitor your are using for your MM) you can simply purchase a ready made one of their frame! Looks to be MM compatible!

For those of you who don’t know, the Canviz is a monitor inside a frame run by a raspberry pi… :) sound familiar?

http://canviz.co/diy/

*am am not affiliated with canviz at all - just excited to have a proper frame tutorial! *

Nedd help as i don´t get it to work, All shows up on the mirror but not display any info on time.
It is for Sweden i try this to work so maybe some one from Sweden can show the config they use to get it to work.
The api is in place so that is ok.

@Mykle1

Good to know, as i was not aware there was a yellow - upper_third or cyan - middle_centre zones available… just the magneta - lower_third for compliments.

top_bar and bottom_bar are light gray
top_left and bottom_left are red
top_center and bottom_center are blue
top_right and bottom_right are green
upper_third is yellow
middle_center is cyan
lower_third is magenta

All these regions will resize as needed.

Have you used MMM-Swipe module. It uses two ultrasonic sensors to detectr right and left motions, I found it quite easy and straightforward

@SoleLo

Read here :

https://forum.magicmirror.builders/topic/1381/ir-frame-doesn-t-rotate

I ordered the IR Touch frame we are talking about here…now two of us have the same frame and that makes it easier to figure out any issues :)

@SoleLo If you’re going to recess the cabinet into the wall, you could make a cheap box out of 2x4’s a few inches bigger than the medicine cabinet to run all of your wiring into and keep it in the wall. Then just pop in some cleats to mount the medicine cabinet into. The displays that I try and use have USB ports on them that give out enough power to run a pi zero so the only cable/cord you would need would be power to the display itself. you could probably just use some cable staples to fasten the cord to the hinge side and keep it fairly clean looking.

@bminer1 said in Revelation! A “Duh” moment with NetworkScanner module.:

@Mykle1 Could you share your Config?

{ module: 'MMM-NetworkScanner', position: 'top_left', config: { devices: [ { ipAddress: "192.168.1.8", name: "BottlePop", icon: "globe"}, { ipAddress: "192.168.1.17", name: "Baby Jesus", icon: "futbol-o"}, { ipAddress: "192.168.1.2", name: "Dove", icon: "medkit"}, { ipAddress: "192.168.1.11", name: "Donna", icon: "venus"}, { ipAddress: "192.168.1.10", name: "Nikki", icon: "coffee"}, { ipAddress: "192.168.1.3", name: "Jason", icon: "fire-extinguisher"}, ], showUnknown: false, // shows devices found on the network even if not specified in the 'devices' option showOffline: true, // shows devices specified in the 'devices' option even when offline showLastSeen: false, // shows when the device was last seen e.g. "Device Name - last seen 5 minutes ago" keepAlive: 300, // how long (in seconds) a device should be considered 'alive' since it was last found on the network updateInterval: 10, // how often (in seconds) the module should scan the network residents: [], } },

@SoleLo said in Taking The Leap! Need MM Family Help:

I don’t really use that medicine cabinet it’s pretty much empty right now

Nice! Then some of the work is already done for you, if you decide to “bury” it.

@pugsly said in Share your config.js right here....:

@1uke_ I would also add a place to download the custom.css file as well.

Perhaps that could be a button below the download config file?

As an amateur, there are a couple things that I just don’t understand about git. I’ve decided to clone my fork of the project to the desktop on my pi, so that I will have another version of my MagicMirror on GitHub. However every time I make a change, it doesn’t show up in git status. When I do git push it asks for my username and password, but still does not work. Is there a way to log on to my account from the command prompt so I can complete these actions?

I can recomend you 3 things:

Check the next documentation

http://rogerdudler.github.io/git-guide/ (simple) https://backlogtool.com/git-guide/en/stepup/stepup1_1.html (some details about branches) http://rogerdudler.github.io/git-guide/

Second one, use this interactive tutorial
https://try.github.io

The last, you can work better using a zsh+oh-my-zsh. This enable to see where branch you are and status repository into the shell prompt.
https://github.com/robbyrussell/oh-my-zsh

Well, the fix was introduced
https://github.com/julianlam/nodebb-plugin-markdown/pull/84

0_1487880299944_68018244.jpg